{"title":"Controllers, Dosing \u0026 Automation","description":"\u003cp\u003eAutomation turns daily jobs into weekly ones. Dosing pumps deliver measured amounts of calcium, alkalinity, magnesium and trace element supplements on a schedule, which keeps parameters far steadier than dosing by hand and matters more the more stony coral you keep.\u003c\/p\u003e\n\u003cp\u003eControllers monitor temperature, pH and water level, switch equipment on and off, and send an alert when something goes outside the range you set. We stock Red Sea, AutoAqua, EcoTech Marine and Aqua Medic units.\u003c\/p\u003e\n\u003cp\u003eStart by measuring how much your tank consumes over a week, then set the dose to match. Automation holds a system where you put it, so the parameters need to be right before you automate them.\u003c\/p\u003e\n\u003cp\u003eSee also \u003ca href=\"\/collections\/sw-test-kits\"\u003eTest Kits\u003c\/a\u003e and \u003ca href=\"\/collections\/sw-auto-top-off\"\u003eAuto Top Off (ATO)\u003c\/a\u003e. Shipped Australia wide from Brisbane.\u003c\/p\u003e","products":[{"product_id":"red-sea-reefdose-2","title":"Red Sea ReefDose 2","description":"\u003cp\u003e\u003cstrong\u003eAutomate two-part dosing without the daily top-up.\u003c\/strong\u003e The Red Sea ReefDose 2 is an app-controlled dosing pump with two independently scheduled heads, built to deliver reef supplements automatically and consistently throughout the day. It suits reef tanks running a two-part calcium and alkalinity program, dosing in increments as small as 0.1 mL on a schedule you set in Red Sea's ReefBeat app.\u003c\/p\u003e\n\u003ch3\u003eKey features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eTwo independent dosing heads\u003c\/strong\u003e - run separate schedules for two different supplements, such as calcium and alkalinity\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e0.1 mL dosing increments, +\/-0.05 mL accuracy\u003c\/strong\u003e - small, frequent doses instead of one daily spike\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUp to 24 scheduled doses per head, per day\u003c\/strong\u003e - spread dosing evenly rather than dumping it in all at once\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWi-Fi and the free ReefBeat app\u003c\/strong\u003e - schedule, adjust and monitor from your phone, no separate base unit required\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree selectable flow rates\u003c\/strong\u003e - Whisper, Regular and Turbo, to suit different dose sizes\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSpec\u003c\/th\u003e\n\u003cth\u003eValue\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eDosing heads\u003c\/td\u003e\n\u003ctd\u003e2, independently scheduled\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDosing accuracy\u003c\/td\u003e\n\u003ctd\u003e+\/-0.05 mL\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDose range per head\u003c\/td\u003e\n\u003ctd\u003e0.2-1000 mL, in 0.1 mL increments\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFlow rate options\u003c\/td\u003e\n\u003ctd\u003eApprox. 15 mL\/min (Whisper), 30 mL\/min (Regular), 45 mL\/min (Turbo)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSchedule granularity\u003c\/td\u003e\n\u003ctd\u003eUp to 24 individually timed doses per head, per day\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDelay between heads\u003c\/td\u003e\n\u003ctd\u003eAdjustable, 15 seconds to 5 minutes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eConnectivity\u003c\/td\u003e\n\u003ctd\u003eWi-Fi (2.4 GHz), Red Sea ReefBeat app - no base unit required\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower supply\u003c\/td\u003e\n\u003ctd\u003e100-240 V AC input, 12 V DC output, up to 10 W\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions (W x D x H)\u003c\/td\u003e\n\u003ctd\u003e13 x 10.5 x 8.5 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTubing\u003c\/td\u003e\n\u003ctd\u003e3 mm ID \/ 5 mm OD - Red Sea specifies TPE tubing, not silicone\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eWhat's included \/ Not included\u003c\/h3\u003e\n\u003cp\u003eIn the box: the ReefDose 2 pump unit, power supply, mounting bracket and a measuring cylinder for calibration.\u003c\/p\u003e\n\u003cp\u003eNot included: dosing tubing and delivery tips, and supplement containers. You'll need a tubing kit, such as the \u003ca href=\"\/products\/red-sea-reefdose-accessory-kit-blue-green\"\u003eRed Sea ReefDose Accessory Kit\u003c\/a\u003e, before you can run your first dose.\u003c\/p\u003e\n\u003ch3\u003eWhich ReefDose do I need?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003e\u003c\/th\u003e\n\u003cth\u003eReefDose 2\u003c\/th\u003e\n\u003cth\u003eReefDose 4\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eDosing heads\u003c\/td\u003e\n\u003ctd\u003e2\u003c\/td\u003e\n\u003ctd\u003e4\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTypical use\u003c\/td\u003e\n\u003ctd\u003eTwo-part dosing, e.g. calcium and alkalinity\u003c\/td\u003e\n\u003ctd\u003eA full multi-part regime, e.g. calcium, alkalinity, magnesium and trace elements\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions (W x D x H)\u003c\/td\u003e\n\u003ctd\u003e13 x 10.5 x 8.5 cm\u003c\/td\u003e\n\u003ctd\u003e22.5 x 10.5 x 8.5 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDose range per head\u003c\/td\u003e\n\u003ctd\u003e0.2-1000 mL, 0.1 mL increments\u003c\/td\u003e\n\u003ctd\u003e0.2-1000 mL, 0.1 mL increments\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eIf you're only running a two-part program, the ReefDose 2 covers it. Add a third or fourth supplement and it's time to step up to the \u003ca href=\"\/products\/red-sea-reefdose-4\"\u003eRed Sea ReefDose 4\u003c\/a\u003e.\u003c\/p\u003e\n\u003ch3\u003eSuitable for, and not suitable for\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eSuitable for marine reef aquariums running scheduled supplement dosing\u003c\/li\u003e\n\u003cli\u003eSuitable for two-part calcium and alkalinity programs, or any two supplements dosed on separate schedules\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNot suitable if you need more than two independently scheduled supplements - choose the four-head ReefDose 4 instead.\u003c\/p\u003e\n\u003ch3\u003eCare and maintenance\u003c\/h3\u003e\n\u003cp\u003eCalibrate each head against the included measuring cylinder when you install new tubing or switch supplements, and recheck periodically - dosing tubing wears with use and can drift out of calibration over time.\u003c\/p\u003e\n\u003ch3\u003eSafety\u003c\/h3\u003e\n\u003cp\u003eThis is a mains-powered device - connect the supplied power unit to a standard outlet, ideally through a GPO protected by an RCD, as with any aquarium electrical equipment. Reef supplements are often alkaline or corrosive: follow the supplement manufacturer's handling instructions, and route tubing so a leak drains away from electronics rather than into them.\u003c\/p\u003e\n\u003ch3\u003eGoes well with\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/red-sea-reefdose-accessory-kit-blue-green\"\u003eRed Sea ReefDose Accessory Kit (Blue+Green)\u003c\/a\u003e - the tubing, tips and holder your ReefDose 2 doesn't come with\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/red-sea-reefdose-4\"\u003eRed Sea ReefDose 4\u003c\/a\u003e - if you outgrow two channels\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWarranty and delivery\u003c\/h3\u003e\n\u003cp\u003eRed Sea's manual states a 24-month limited warranty on the pump, in addition to your rights under the Australian Consumer Law. Ships on standard parcel freight.\u003c\/p\u003e\n\u003ch3\u003eCommon questions\u003c\/h3\u003e\n\u003ch4\u003eDoes the ReefDose 2 need a separate controller?\u003c\/h4\u003e\n\u003cp\u003eNo - it connects directly to your Wi-Fi and is scheduled entirely from Red Sea's free ReefBeat app; no base unit or hub is required.\u003c\/p\u003e\n\u003ch4\u003eCan I run four supplements from a ReefDose 2?\u003c\/h4\u003e\n\u003cp\u003eNo - it has two independent heads. For a four-part regime, step up to the ReefDose 4.\u003c\/p\u003e\n\u003ch4\u003eDoes it come with tubing?\u003c\/h4\u003e\n\u003cp\u003eNo. Red Sea sells the pump and the dosing tubing separately - see the ReefDose Accessory Kit for colour-coded lines and tips.\u003c\/p\u003e\n\u003ch4\u003eWhat's the smallest dose it can deliver?\u003c\/h4\u003e\n\u003cp\u003e0.2 mL per head, in 0.1 mL increments - fine enough for small nano systems as well as larger reefs.\u003c\/p\u003e","brand":"RedSea","offers":[{"title":"Default Title","offer_id":54774161342755,"sku":"RED830","price":495.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0972\/7236\/5347\/files\/red-sea-reefdose-2-43876697080099.webp?v=1790239294"},{"product_id":"red-sea-reefdose-4","title":"Red Sea ReefDose 4","description":"\u003cp\u003e\u003cstrong\u003eRun a full four-part regime from one pump.\u003c\/strong\u003e The Red Sea ReefDose 4 is an app-controlled dosing pump with four independently scheduled heads, built to automate a complete reef supplement program - calcium, alkalinity, magnesium and trace elements - from a single unit. Doses run in increments as small as 0.1 mL, scheduled from Red Sea's ReefBeat app.\u003c\/p\u003e\n\u003ch3\u003eKey features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFour independent dosing heads\u003c\/strong\u003e - a separate schedule for each of calcium, alkalinity, magnesium and trace elements\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e0.1 mL dosing increments, +\/-0.05 mL accuracy\u003c\/strong\u003e - small, frequent doses instead of one daily spike\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUp to 24 scheduled doses per head, per day\u003c\/strong\u003e - spread every supplement evenly across the day\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWi-Fi and the free ReefBeat app\u003c\/strong\u003e - schedule, adjust and monitor all four channels from your phone\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree selectable flow rates\u003c\/strong\u003e - Whisper, Regular and Turbo, to suit different dose sizes\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSpec\u003c\/th\u003e\n\u003cth\u003eValue\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eDosing heads\u003c\/td\u003e\n\u003ctd\u003e4, independently scheduled\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDosing accuracy\u003c\/td\u003e\n\u003ctd\u003e+\/-0.05 mL\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDose range per head\u003c\/td\u003e\n\u003ctd\u003e0.2-1000 mL, in 0.1 mL increments\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFlow rate options\u003c\/td\u003e\n\u003ctd\u003eApprox. 15 mL\/min (Whisper), 30 mL\/min (Regular), 45 mL\/min (Turbo)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSchedule granularity\u003c\/td\u003e\n\u003ctd\u003eUp to 24 individually timed doses per head, per day\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDelay between heads\u003c\/td\u003e\n\u003ctd\u003eAdjustable, 15 seconds to 5 minutes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eConnectivity\u003c\/td\u003e\n\u003ctd\u003eWi-Fi (2.4 GHz), Red Sea ReefBeat app - no base unit required\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower supply\u003c\/td\u003e\n\u003ctd\u003e100-240 V AC input, 12 V DC output, up to 10 W\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions (W x D x H)\u003c\/td\u003e\n\u003ctd\u003e22.5 x 10.5 x 8.5 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTubing\u003c\/td\u003e\n\u003ctd\u003e3 mm ID \/ 5 mm OD - Red Sea specifies TPE tubing, not silicone\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eWhat's included \/ Not included\u003c\/h3\u003e\n\u003cp\u003eIn the box: the ReefDose 4 pump unit, power supply, mounting bracket and a measuring cylinder for calibration.\u003c\/p\u003e\n\u003cp\u003eNot included: dosing tubing and delivery tips, and supplement containers. You'll need a tubing kit, such as the \u003ca href=\"\/products\/red-sea-reefdose-accessory-kit-blue-green\"\u003eRed Sea ReefDose Accessory Kit\u003c\/a\u003e, before you can run your first dose.\u003c\/p\u003e\n\u003ch3\u003eWhich ReefDose do I need?\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003e\u003c\/th\u003e\n\u003cth\u003eReefDose 2\u003c\/th\u003e\n\u003cth\u003eReefDose 4\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eDosing heads\u003c\/td\u003e\n\u003ctd\u003e2\u003c\/td\u003e\n\u003ctd\u003e4\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTypical use\u003c\/td\u003e\n\u003ctd\u003eTwo-part dosing, e.g. calcium and alkalinity\u003c\/td\u003e\n\u003ctd\u003eA full multi-part regime, e.g. calcium, alkalinity, magnesium and trace elements\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions (W x D x H)\u003c\/td\u003e\n\u003ctd\u003e13 x 10.5 x 8.5 cm\u003c\/td\u003e\n\u003ctd\u003e22.5 x 10.5 x 8.5 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDose range per head\u003c\/td\u003e\n\u003ctd\u003e0.2-1000 mL, 0.1 mL increments\u003c\/td\u003e\n\u003ctd\u003e0.2-1000 mL, 0.1 mL increments\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eIf you're already running four supplements, or plan to, the ReefDose 4 gives each one its own head and schedule. Only dosing two? The smaller \u003ca href=\"\/products\/red-sea-reefdose-2\"\u003eRed Sea ReefDose 2\u003c\/a\u003e covers it for less outlay.\u003c\/p\u003e\n\u003ch3\u003eSuitable for, and not suitable for\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eSuitable for full four-part dosing programs - calcium, alkalinity, magnesium and trace elements - each on an independent schedule\u003c\/li\u003e\n\u003cli\u003eSuitable for reef tanks that have outgrown a two-head doser\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNot suitable if you only run one or two supplements - the ReefDose 2 does that job without paying for heads you won't use.\u003c\/p\u003e\n\u003ch3\u003eCare and maintenance\u003c\/h3\u003e\n\u003cp\u003eRecalibrate each of the four heads against the included measuring cylinder whenever you fit new tubing or change a supplement, since tubing wears with use and dosing accuracy drifts as a result. With four lines running, label each one against your dosing chart so maintenance stays quick.\u003c\/p\u003e\n\u003ch3\u003eSafety\u003c\/h3\u003e\n\u003cp\u003eThis is a mains-powered device, so connect it through a standard GPO protected by an RCD, as with any aquarium electrical equipment. With four supplements running - often alkaline or corrosive - follow each manufacturer's handling instructions and keep the unit mounted above the dosing containers so a tubing fault drains away from the electronics.\u003c\/p\u003e\n\u003ch3\u003eGoes well with\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/red-sea-reefdose-accessory-kit-blue-green\"\u003eRed Sea ReefDose Accessory Kit (Blue+Green)\u003c\/a\u003e - the tubing, tips and holder your ReefDose 4 doesn't come with\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/red-sea-reefdose-4-tube-holder-includes-tips\"\u003eRed Sea ReefDose 4 Tube Holder\u003c\/a\u003e - mounts all four lines above the waterline\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWarranty and delivery\u003c\/h3\u003e\n\u003cp\u003eRed Sea's manual states a 24-month limited warranty on the pump, in addition to your rights under the Australian Consumer Law. Ships on standard parcel freight.\u003c\/p\u003e\n\u003ch3\u003eCommon questions\u003c\/h3\u003e\n\u003ch4\u003eIs the ReefDose 4 harder to set up than the ReefDose 2?\u003c\/h4\u003e\n\u003cp\u003eNo - it uses the same ReefBeat app and per-head scheduling; you're just configuring four channels instead of two.\u003c\/p\u003e\n\u003ch4\u003eCan I dose calcium, alkalinity, magnesium and trace elements all from one unit?\u003c\/h4\u003e\n\u003cp\u003eYes - that's exactly what the four heads are for, each running its own independent schedule.\u003c\/p\u003e\n\u003ch4\u003eDoes it come with tubing?\u003c\/h4\u003e\n\u003cp\u003eNo. Red Sea sells the pump and the dosing tubing separately - see the ReefDose Accessory Kit for colour-coded lines and tips.\u003c\/p\u003e\n\u003ch4\u003eHow many doses a day can each head run?\u003c\/h4\u003e\n\u003cp\u003eUp to 24 individually timed doses per head, with the delay between heads adjustable from 15 seconds to 5 minutes.\u003c\/p\u003e","brand":"RedSea","offers":[{"title":"Default Title","offer_id":54774161375523,"sku":"RED831","price":675.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0972\/7236\/5347\/files\/red-sea-reefdose-4-43876697375011.webp?v=1790239292"},{"product_id":"red-sea-reefdose-head-tube-hose-barbs","title":"Red Sea ReefDose Head Tube + Hose Barbs","description":"\u003cp\u003e\u003cstrong\u003eThe wear part that keeps dosing accurate over time.\u003c\/strong\u003e This genuine Red Sea head tube with hose barbs is the peristaltic tube inside a ReefDose dosing head — the flexible section the rollers squeeze to move liquid, and the part that wears fastest.\u003c\/p\u003e\n\u003ch3\u003eKey features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eGenuine Red Sea factory part with matching hose barbs\u003c\/li\u003e\n\u003cli\u003eDirect-fit peristaltic replacement for one dosing head\u003c\/li\u003e\n\u003cli\u003eRestores accurate, factory-calibrated dose volume\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWill this fit my ReefDose?\u003c\/h3\u003e\n\u003cp\u003eYes. The head tube is the same across the ReefDose 2 and ReefDose 4 — one tube per dosing head.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003eReefDose 2, ReefDose 4 (one tube per dosing head)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eManufacturer part number\u003c\/th\u003e\n\u003ctd\u003eR35344\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSold as\u003c\/th\u003e\n\u003ctd\u003eSingle unit\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFitting\u003c\/th\u003e\n\u003ctd\u003eNo tools required — unclips from the head\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eSuitable for, and not suitable for\u003c\/h3\u003e\n\u003cp\u003eSuitable when a channel is under-dosing, dosing unevenly, or the tube shows visible flattening or cracking where the rollers run. Not the fix for a head that won't turn at all — that's the gear motor.\u003c\/p\u003e\n\u003ch3\u003eCare and maintenance\u003c\/h3\u003e\n\u003cp\u003ePeristaltic tubing is a consumable. Red Sea recommends replacing it roughly once a year, more often on additives that are thick or crystallising, and recalibrating the head afterwards.\u003c\/p\u003e\n\u003ch3\u003eWarranty and delivery\u003c\/h3\u003e\n\u003cp\u003eCovered by Red Sea's standard spare parts warranty against manufacturing defects, in addition to your rights under Australian Consumer Law. Standard parcel delivery.\u003c\/p\u003e\n\u003ch3\u003eCommon questions\u003c\/h3\u003e\n\u003ch4\u003eHow often should I replace the head tube?\u003c\/h4\u003e\n\u003cp\u003eRoughly once a year under normal use. Thicker or crystallising additives, like some calcium or alkalinity supplements, wear the tube faster.\u003c\/p\u003e\n\u003ch4\u003eDo I need to recalibrate after fitting a new tube?\u003c\/h4\u003e\n\u003cp\u003eYes — check delivered volume with the ReefDose Measuring Cylinder before trusting the schedule again.\u003c\/p\u003e\n\u003ch4\u003eMy channel is under-dosing — is this the fix?\u003c\/h4\u003e\n\u003cp\u003eUsually, yes. A worn head tube is the most common cause of gradual under-dosing. If the head won't turn at all, replace the gear motor instead.\u003c\/p\u003e","brand":"RedSea","offers":[{"title":"Default Title","offer_id":54774161834275,"sku":"RED838","price":24.95,"currency_code":"AUD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0972\/7236\/5347\/files\/red-sea-reefdose-head-tube-h-43876698259747.webp?v=1790239292"},{"product_id":"red-sea-reefato-system","title":"Red Sea ReefATO System","description":"\u003cp\u003e\u003cstrong\u003eAutomatic top-off ends the daily evaporation top-up.\u003c\/strong\u003e The Red Sea ReefATO+ is a self-contained top-off system for reef and marine aquariums, replacing water lost to evaporation before salinity drifts. A solid-state EC sensor with titanium probes drives a variable-flow pump rated to 300 L\/h at zero head and 2.5 m of lift, throttling back to around 72 L\/h near target level. It suits any marine sump or display within that head and flow range, provided you supply the reservoir and top-off water.\u003c\/p\u003e\n\n\u003ch3\u003eKey features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eSolid-state EC sensor\u003c\/strong\u003e — titanium probes with no float arm or optical window to jam, fog or scratch.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAutomatic flow throttling\u003c\/strong\u003e — the pump settles to roughly 72 L\/h near target level instead of surging at full flow.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIndependent leak detector\u003c\/strong\u003e — a separate titanium probe disables Auto-Fill and stops the pump if it senses water where it shouldn't be.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBackup high-level probe\u003c\/strong\u003e — a second trip point set roughly 2.5 cm above the normal pump-off probe guards against an overfill.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReefBeat app control\u003c\/strong\u003e — level and temperature history plus fault notifications over Wi-Fi, with up to 28 days logged.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eServiceable pump\u003c\/strong\u003e — the impeller and pump head are designed to be opened and cleaned, not replaced as a sealed unit.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMagnetic mounting\u003c\/strong\u003e — sensor holder and tube clips attach to glass up to 12 mm thick without drilling.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eSpecification\u003c\/th\u003e\n\u003cth\u003eDetail\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eModel\u003c\/td\u003e\n\u003ctd\u003eRed Sea ReefATO+ (SKU RED901)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eType\u003c\/td\u003e\n\u003ctd\u003eAutomatic top-off (ATO) system for reef and marine aquariums\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWater level sensor\u003c\/td\u003e\n\u003ctd\u003eSolid-state EC technology, titanium probes, multi-input\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBuilt-in thermometer\u003c\/td\u003e\n\u003ctd\u003eAccuracy ±0.1°C, logged every 15 minutes for up to 28 days\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLevel control band\u003c\/td\u003e\n\u003ctd\u003e3 mm between pump-on and pump-off probes; backup probe approximately 2.5 cm above the normal pump-off probe\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTop-off pump\u003c\/td\u003e\n\u003ctd\u003eVariable-flow, serviceable 12 V DC pump, 4.5 cm diameter\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePump power consumption\u003c\/td\u003e\n\u003ctd\u003e6–10 W, varies with duty\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePump maximum flow\u003c\/td\u003e\n\u003ctd\u003e300 L\/h at zero head\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePump maximum head\u003c\/td\u003e\n\u003ctd\u003e2.5 m\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eRegulated top-off flow\u003c\/td\u003e\n\u003ctd\u003eApproximately 72 L\/h once the pump throttles down near target level\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eLeak detector\u003c\/td\u003e\n\u003ctd\u003eTitanium probe; disables Auto-Fill and the pump immediately on detection\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTubing supplied\u003c\/td\u003e\n\u003ctd\u003e3 m silicone tubing, 5 mm internal diameter, 1.5 mm wall\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCable lengths\u003c\/td\u003e\n\u003ctd\u003ePump, sensor and leak-detector cables 3 m each; power-supply lead 2 m\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMounting\u003c\/td\u003e\n\u003ctd\u003eMagnetic bracket and sensor holder fit glass up to 12 mm; tube clips fit 4–12 mm glass\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eConnectivity\u003c\/td\u003e\n\u003ctd\u003eReefBeat app (iOS and Android) over Wi-Fi\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWater compatibility\u003c\/td\u003e\n\u003ctd\u003eRO\/DI through to full-strength saltwater\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInstallation environment\u003c\/td\u003e\n\u003ctd\u003eIndoor use only; controller is not itself waterproof\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMains input voltage\u003c\/td\u003e\n\u003ctd\u003eNot published by Red Sea for the Australian market — check the rating printed on the supplied power pack\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eManufacturer warranty\u003c\/td\u003e\n\u003ctd\u003e2 years from purchase; pump impeller (a wear item) covered for 6 months\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eSuitable for, and not suitable for\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eSuitable for:\u003c\/strong\u003e reef and marine tanks or sumps that need evaporation top-off; systems where salinity stability matters, such as coral-heavy reef tanks; glass up to 12 mm thick, for the magnetic mount; and setups within reach of home Wi-Fi for ReefBeat notifications and logging.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eNot suitable for:\u003c\/strong\u003e sumps needing more than 300 L\/h of make-up water or more than 2.5 m of lift from reservoir to tank; anyone wanting one unit to dose additives as well as top-off water, since this replaces evaporation only; and locations without a standard wall power outlet within 2 m of the controller. The system does not include a top-off reservoir — it pumps from a container you supply.\u003c\/p\u003e\n\n\u003ch3\u003eWarranty and Australian notes\u003c\/h3\u003e\n\u003cp\u003eRed Sea covers the ReefATO+ for 2 years from the date of purchase against manufacturer defects in materials and workmanship; the pump impeller is a wear item, covered for 6 months only. This warranty applies in addition to the consumer guarantees you already hold under Australian Consumer Law, which exist regardless of any manufacturer term. The included power supply plugs into a standard AU wall outlet; Red Sea does not publish a specific mains input voltage rating for the pack on its Australian materials, so check the label printed on the unit itself before use. The controller is for indoor use only and is not waterproof, so mount it clear of splash zones. Freight-wise it is classed as a standard parcel item, not oversize or special-order.\u003c\/p\u003e\n\n\u003ch3\u003eCommon questions\u003c\/h3\u003e\n\u003ch4\u003eDoes the ReefATO+ include a water reservoir?\u003c\/h4\u003e\n\u003cp\u003eNo. It pumps from a container you supply. Use a sealed, food-grade container sized to at least a week of expected evaporation, placed within the pump's 2.5 m head and 300 L\/h limits.\u003c\/p\u003e\n\u003ch4\u003eCan it dose anything other than top-off water?\u003c\/h4\u003e\n\u003cp\u003eNo. It replaces evaporated water only. A separate doser is needed for trace elements, buffers or any other supplement.\u003c\/p\u003e\n\u003ch4\u003eWhat happens if the sensor loses contact with the water?\u003c\/h4\u003e\n\u003cp\u003eThe unit shuts the pump down automatically. The same cutoff also trips on an abnormally long pump run, a blocked pump, a dry reservoir, or a detected leak, and requires you to resume operation via the button or app once cleared.\u003c\/p\u003e\n\u003ch4\u003eIs the pump repairable if it wears out?\u003c\/h4\u003e\n\u003cp\u003eYes. Red Sea designs the pump to be serviced rather than replaced whole, though the impeller itself is a wear part covered for 6 months rather than the full 2-year warranty.\u003c\/p\u003e\n\u003ch4\u003eHow does the backup high-level probe work?\u003c\/h4\u003e\n\u003cp\u003eIf the normal pump-off probe fails to detect the rising water level, a second probe positioned roughly 2.5 cm higher cuts the pump before it can overfill the sump.\u003c\/p\u003e","brand":"RedSea","offers":[{"title":"Default Title","offer_id":54774162620707,"sku":"RED901","price":378.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0972\/7236\/5347\/files\/red-sea-reefato-system-46119455686947.webp?v=1790239296"},{"product_id":"reefsense-usb-power-connector","title":"ReefSense USB Power Connector","description":"\u003cp\u003e\u003cstrong\u003ePower for a ReefSense probe with no controller involved.\u003c\/strong\u003e The Red Sea ReefSense USB Power Connector runs a ReefSense probe from USB power on its own, so it can report over Bluetooth through the ReefBeat app without being plugged into a ReefControl Lite or Pro. It is the accessory Red Sea specifies for using a ReefSense probe remotely — away from a controller, or before you own one at all.\u003c\/p\u003e\n\u003cp\u003eIt is a power lead, not a controller substitute: readings taken this way display live in the app, but Red Sea does not log or trend them the way a controller-connected probe is.\u003c\/p\u003e\n\u003ch3\u003eKey features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFrees a probe from the controller\u003c\/strong\u003e — power it from any USB source and read it over Bluetooth instead of a ReefControl port.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGenuine Red Sea accessory\u003c\/strong\u003e — the connector Red Sea specifies for standalone ReefSense probe use.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWorks with every ReefSense probe\u003c\/strong\u003e — pH \u0026amp; Temperature, Salinity \u0026amp; Temperature, ORP and Temperature all use the same USB power path.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eHandy before you own a controller\u003c\/strong\u003e — check a probe or take a one-off reading without buying a ReefControl Lite or Pro first.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's included\u003c\/h3\u003e\n\u003cp\u003eOne ReefSense USB Power Connector. The probe itself and a USB power source are sold separately.\u003c\/p\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eStore SKU\u003c\/th\u003e\n\u003ctd\u003eBA9037\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eManufacturer part number\u003c\/th\u003e\n\u003ctd\u003eR35838 (ReefSense USB-C Connector)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eUSB power connector\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePowers\u003c\/th\u003e\n\u003ctd\u003eAny ReefSense digital probe\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eUse case\u003c\/th\u003e\n\u003ctd\u003eStandalone\/remote Bluetooth power, away from a ReefControl controller\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApp\u003c\/th\u003e\n\u003ctd\u003eReefBeat — live reading, no logging in standalone mode\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWater type\u003c\/th\u003e\n\u003ctd\u003eMarine \/ reef\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eWill it fit my system?\u003c\/h3\u003e\n\u003cp\u003eIt works with any ReefSense probe — pH \u0026amp; Temperature, Salinity \u0026amp; Temperature, ORP or Temperature — regardless of whether you own a ReefControl Lite, Pro or no controller at all. It is not required for normal use: a probe plugged into a ReefControl controller is already powered through that port. This connector is only needed when you want a probe running independently of a controller.\u003c\/p\u003e\n\u003ch3\u003eSuitable for, and not suitable for\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eSuitable for:\u003c\/strong\u003e spot-checking a ReefSense probe before buying a controller, running a probe remotely (a quarantine tank or frag system, for example), or powering a probe for Bluetooth-only use.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eNot suitable for:\u003c\/strong\u003e continuous logged monitoring or automation — a probe run this way is not connected to a ReefControl Lite or Pro, so it will not trend data over time or trigger ReefControl Power switching. For that, plug the probe into a controller instead.\u003c\/p\u003e\n\u003ch3\u003eGoes well with\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/products\/reefsense-temperature-probe\"\u003eRed Sea ReefSense Temperature Probe\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/products\/reefsense-ph-temp-probe\"\u003eRed Sea ReefSense pH \u0026amp; Temperature Probe\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/reefcontrol-lite\"\u003eRed Sea ReefControl Lite\u003c\/a\u003e — for continuous, logged monitoring instead of standalone use.\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/reefsense-single-probe-holder\"\u003eRed Sea ReefSense Single Probe Holder\u003c\/a\u003e — mounts the probe once it is powered.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWarranty and delivery\u003c\/h3\u003e\n\u003cp\u003eAny manufacturer warranty Red Sea offers on this accessory applies in addition to your rights under the Australian Consumer Law, which are not limited or excluded by it.\u003c\/p\u003e\n\u003cp\u003eShips as a standard small parcel.\u003c\/p\u003e\n\u003ch3\u003eCommon questions\u003c\/h3\u003e\n\u003ch4\u003eDo I need this to use a ReefSense probe?\u003c\/h4\u003e\n\u003cp\u003eNo, not if the probe is plugged into a ReefControl Lite or Pro — the controller powers it through the port. This connector is only for running a probe away from a controller.\u003c\/p\u003e\n\u003ch4\u003eDoes a probe powered this way still log to the ReefBeat app?\u003c\/h4\u003e\n\u003cp\u003eIt displays a live reading, but Red Sea does not log or trend it the way a controller-connected probe is, so this mode suits a quick check rather than ongoing monitoring.\u003c\/p\u003e\n\u003ch4\u003eWhich probes does it work with?\u003c\/h4\u003e\n\u003cp\u003eAny ReefSense digital probe — pH \u0026amp; Temperature, Salinity \u0026amp; Temperature, ORP or standalone Temperature.\u003c\/p\u003e\n\u003ch4\u003eCan I use it to try a probe before buying a controller?\u003c\/h4\u003e\n\u003cp\u003eYes — this is one of the situations Red Sea specifies it for, powering the probe over USB so it reports over Bluetooth through the ReefBeat app without a controller in the loop.\u003c\/p\u003e","brand":"RedSea","offers":[{"title":"Default Title","offer_id":55242223288611,"sku":"BA9037","price":45.0,"currency_code":"AUD","in_stock":true}]},{"product_id":"reefcontrol-power-6-panel","title":"ReefControl Power 6 Panel","description":"\u003cp\u003e\u003cstrong\u003eLocal, app-free control for every outlet on your Power 6.\u003c\/strong\u003e The Red Sea ReefControl Power 6 Panel is an optional accessory that adds physical, backlit ON\/OFF buttons for all six outlets on a ReefControl Power 6 smart power centre, plus one master button that kills all six at once — so you can cut power at the cabinet without opening the ReefBeat app. It connects to the Power 6 unit with a 2 m data cable and draws its own power through that connection, so there's no separate plug or battery to manage.\u003c\/p\u003e\u003ch3\u003eKey features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eBacklit button per outlet\u003c\/strong\u003e — six individually lit ON\/OFF buttons let you see and switch each outlet's state at a glance, from the cabinet rather than a phone.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMaster ON\/OFF button\u003c\/strong\u003e — cuts or restores all six outlets together, handy for maintenance days when everything needs to come off at once.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNo separate power supply\u003c\/strong\u003e — powered entirely through its data-cable connection to the Power 6 unit.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWorks alongside the ReefBeat app\u003c\/strong\u003e — local control at the panel and remote control in the app stay in sync; using one doesn't lock out the other.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eConnects to\u003c\/th\u003e\n\u003ctd\u003eRed Sea ReefControl Power 6 (data cable, approx. 2 m supplied)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eOutlets controlled\u003c\/th\u003e\n\u003ctd\u003e6, individually, plus 1 master button\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePower source\u003c\/th\u003e\n\u003ctd\u003eDrawn through the data connection to the Power 6 unit — no separate power supply\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eManufacturer part number\u003c\/th\u003e\n\u003ctd\u003eR35819\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFits\u003c\/h3\u003e\u003cp\u003eBuilt specifically for the Red Sea ReefControl Power 6, sold in Australia as a 6-outlet, 2400 W-rated power centre. It is not compatible with the 8-outlet ReefControl Power 8 sold in other regions, which uses its own matching Control Panel 8. Also sold pre-fitted as part of the ReefControl Power 6 Deluxe bundle — if you already own a plain Power 6, this panel adds the same control without replacing the unit.\u003c\/p\u003e\u003ch3\u003eSuitable for, and not suitable for\u003c\/h3\u003e\u003cp\u003eSuitable for any ReefControl Power 6 owner who wants local switching at the cabinet. Not a stand-alone power strip — it has no outlets of its own and does nothing without a Power 6 unit connected to it.\u003c\/p\u003e\u003ch3\u003eWarranty and delivery\u003c\/h3\u003e\u003cp\u003eCovered by Red Sea's manufacturer warranty, in addition to your consumer guarantee rights under Australian Consumer Law. Ships as a small parcel item at standard rates.\u003c\/p\u003e\u003ch3\u003eCommon questions\u003c\/h3\u003e\u003ch4\u003eDoes it work without the ReefBeat app?\u003c\/h4\u003e\u003cp\u003eYes — the buttons switch outlets locally regardless of whether a phone is connected. The app gives you scheduling and remote access on top.\u003c\/p\u003e\u003ch4\u003eCan I add it to a Power 6 I already own?\u003c\/h4\u003e\u003cp\u003eYes, it's sold as a standalone accessory that connects to an existing Power 6 unit with the supplied data cable.\u003c\/p\u003e\u003ch4\u003eWill it fit my Power 8?\u003c\/h4\u003e\u003cp\u003eNo — the Power 8 (sold in some overseas markets) uses a different eight-button Control Panel 8, not this unit.\u003c\/p\u003e","brand":"RedSea","offers":[{"title":"Default Title","offer_id":55242223321379,"sku":"BA9023","price":170.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0972\/7236\/5347\/files\/product-20251029-775a9a371468912ae46573456e9a6162.jpg?v=1791169871"},{"product_id":"reefcontrol-power-6","title":"ReefControl Power 6","description":"\u003cp\u003e\u003cstrong\u003eSix outlets of app-controlled power, sized for the Australian market.\u003c\/strong\u003e The Red Sea ReefControl Power 6 is a smart power distribution unit for reef and marine tanks: six individually switched outlets rated to 2,400W combined on the Australian 240V model, run and scheduled from the ReefBeat app, with a dedicated port for the ReefControl Grounding Probe. It suits a reefer who wants their pumps, heaters and lighting switched, scheduled and monitored from one hub instead of a row of mechanical timers.\u003c\/p\u003e\u003ch3\u003eKey features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e6 individually controllable outlets\u003c\/strong\u003e — 2,400W combined rating on the Australian 240V unit, so each device can be switched, scheduled or grouped on its own.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePer-outlet power monitoring\u003c\/strong\u003e — see what each connected device is actually drawing, useful for spotting a failing pump or heater before it fails outright.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFeed mode and night mode\u003c\/strong\u003e — pause return pumps and skimmers for feeding, or step connected lighting down on a schedule, without manually flicking switches.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDirect temperature probe input\u003c\/strong\u003e — connect a temperature probe for heater backup and failure alerts independent of your main controller.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrounding probe port\u003c\/strong\u003e — a dedicated socket for the Red Sea ReefControl Grounding Probe, sold separately.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWorks with third-party equipment\u003c\/strong\u003e — any mains-powered device can be plugged in and scheduled, not just Red Sea gear.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eOutlets\u003c\/th\u003e\n\u003ctd\u003e6, individually controllable\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTotal power rating (AU 240V model)\u003c\/th\u003e\n\u003ctd\u003e2,400W\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDimensions (L x W x H)\u003c\/th\u003e\n\u003ctd\u003e41 x 8.5 x 7.7 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePower (per outlet)\u003c\/th\u003e\n\u003ctd\u003eNot published by Red Sea — see below\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eConnectivity\u003c\/th\u003e\n\u003ctd\u003eWi-Fi via ReefBeat app\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGrounding probe port\u003c\/th\u003e\n\u003ctd\u003eYes, probe sold separately\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApp\u003c\/th\u003e\n\u003ctd\u003eReefBeat\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003cp\u003eRed Sea publishes a total combined power rating for the unit rather than a per-outlet figure — plan your heaviest single load (typically a heater or return pump) against the 2,400W total, not against an assumed even split across all six outlets.\u003c\/p\u003e\u003ch3\u003eWhat's included\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eReefControl Power 6 unit with 6 mains outlets\u003c\/li\u003e\n\u003cli\u003eWi-Fi connectivity for ReefBeat app control\u003c\/li\u003e\n\u003cli\u003eTemperature probe input\u003c\/li\u003e\n\u003cli\u003eGrounding probe port (probe sold separately)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eNot included\u003c\/h3\u003e\u003cp\u003eThis is the standard unit — it does not include the manual control panel with individual on\/off pushbuttons. If you want physical switches at the unit as well as app control, see the ReefControl Power 6 Deluxe.\u003c\/p\u003e\u003ch3\u003eWhich ReefControl Power do I need?\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003c\/th\u003e\n\u003cth\u003eReefControl Power 6\u003c\/th\u003e\n\u003cth\u003eReefControl Power 6 Deluxe\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eOutlets\u003c\/th\u003e\n\u003ctd\u003e6\u003c\/td\u003e\n\u003ctd\u003e6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTotal power (AU)\u003c\/th\u003e\n\u003ctd\u003e2,400W\u003c\/td\u003e\n\u003ctd\u003e2,400W\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApp control\u003c\/th\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eManual control panel\u003c\/th\u003e\n\u003ctd\u003eNo\u003c\/td\u003e\n\u003ctd\u003eYes — backlit on\/off pushbutton per outlet, plus a master switch\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003cp\u003eChoose the standard Power 6 if you're happy switching everything from the ReefBeat app. Choose the Deluxe if you want physical buttons at the unit too — useful during a Wi-Fi outage, or for anyone who just prefers a switch they can see and feel.\u003c\/p\u003e\u003ch3\u003eSuitable for, and not suitable for\u003c\/h3\u003e\u003cp\u003eSuitable for switching and scheduling pumps, heaters, lighting and other mains-powered equipment on a reef or marine system, with or without other Red Sea equipment already installed. Not a substitute for a dedicated RCD-protected circuit, and not rated to run every outlet at once near its full 2,400W if your heaviest equipment already uses a large share of that total.\u003c\/p\u003e\u003ch3\u003eSafety\u003c\/h3\u003e\u003cp\u003eRun on an RCD-protected circuit. Keep drip loops on every cable entering or leaving the unit, and mount it above likely water level. Total load across all six outlets should stay within the 2,400W AU rating.\u003c\/p\u003e\u003ch3\u003eGoes well with\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eReefControl Lite\u003c\/strong\u003e — adds probe monitoring alongside the Power unit's switching.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReefControl Grounding Probe\u003c\/strong\u003e — plugs into the dedicated port to reduce stray voltage.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReefControl Power 6 Deluxe\u003c\/strong\u003e — the same unit with a physical control panel, if you outgrow app-only switching.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWarranty and delivery\u003c\/h3\u003e\u003cp\u003eCovered by Red Sea's manufacturer warranty, in addition to your consumer guarantee rights under Australian Consumer Law. Standard parcel delivery.\u003c\/p\u003e\u003ch3\u003eCommon questions\u003c\/h3\u003e\u003ch4\u003eCan I run this without a ReefControl Lite or Pro hub?\u003c\/h4\u003e\u003cp\u003eYes. ReefControl Power operates on its own through the ReefBeat app; a ReefControl Lite or Pro hub adds probe-based monitoring and automation on top of it.\u003c\/p\u003e\u003ch4\u003eWill all six outlets run at once at full load?\u003c\/h4\u003e\u003cp\u003eThe unit is rated 2,400W combined across all six outlets on the Australian model — check your connected equipment's total draw against that figure rather than assuming each outlet gets an even, independent 400W.\u003c\/p\u003e\u003ch4\u003eDoes it need the grounding probe?\u003c\/h4\u003e\u003cp\u003eNo, it's optional. It reduces stray voltage in the tank water, which mainly shows up as noisier readings on connected probes rather than a functional problem with the Power unit itself.\u003c\/p\u003e\u003ch4\u003eCan I connect more than one ReefControl Power unit?\u003c\/h4\u003e\u003cp\u003eYes — up to two Power units can be linked to the one ReefBeat account for larger systems.\u003c\/p\u003e","brand":"RedSea","offers":[{"title":"Default Title","offer_id":55242223386915,"sku":"BA9022","price":565.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0972\/7236\/5347\/files\/reefcontrol-power-6-10268546367779-1-dq.webp?v=1790372841"},{"product_id":"reefcontrol-reefsense-port-expander","title":"ReefControl ReefSense Port Expander","description":"\u003cp\u003e\u003cstrong\u003eTakes a ReefControl Pro from four probes to seven.\u003c\/strong\u003e The Red Sea ReefSense 4-Port Expander adds extra, fully interchangeable ReefSense ports to a ReefControl Pro hub, so a growing reef or freshwater setup isn't capped at four probes and sensors. Any ReefSense probe — pH, temperature, salinity, ORP or the leak detector — works in any port, so there's no fixed layout to plan around.\u003c\/p\u003e\u003ch3\u003eKey features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eTakes ReefControl Pro from 4 to 7 total ReefSense ports\u003c\/strong\u003e — add probes as your monitoring needs grow, rather than buying a bigger hub.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUniversal ports\u003c\/strong\u003e — any ReefSense probe type plugs into any port on the expander, no dedicated slots.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGenuine Red Sea ReefSense accessory\u003c\/strong\u003e — matched firmware and connector, no third-party adapters.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eAdds\u003c\/th\u003e\n\u003ctd\u003eAdditional ReefSense ports, taking a ReefControl Pro to 7 total\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePort type\u003c\/th\u003e\n\u003ctd\u003eUniversal — accepts any ReefSense probe or sensor\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eFits\u003c\/h3\u003e\u003cp\u003eCompatible with the Red Sea ReefControl Pro only. Red Sea's own materials are explicit that it does not work with the entry-level ReefControl Lite, which has no expansion capability. Red Sea has not published the expander's own dimensions, connector type, cable length or power source on its Australian or global product pages at the time of writing — if you need those figures confirmed before ordering, ask us and we'll check with Red Sea directly.\u003c\/p\u003e\u003ch3\u003eSuitable for, and not suitable for\u003c\/h3\u003e\u003cp\u003eSuitable for any ReefControl Pro owner who wants to run more than four ReefSense probes at once. Not suitable for, and not compatible with, ReefControl Lite.\u003c\/p\u003e\u003ch3\u003eWarranty and delivery\u003c\/h3\u003e\u003cp\u003eCovered by Red Sea's manufacturer warranty, in addition to your consumer guarantee rights under Australian Consumer Law. Ships as a small parcel item at standard rates.\u003c\/p\u003e\u003ch3\u003eCommon questions\u003c\/h3\u003e\u003ch4\u003eWill this work with ReefControl Lite?\u003c\/h4\u003e\u003cp\u003eNo. Red Sea specifies the 4-Port Expander for ReefControl Pro only.\u003c\/p\u003e\u003ch4\u003eCan I choose which probes go in which port?\u003c\/h4\u003e\u003cp\u003eThe ports are universal, so any ReefSense probe works in any port — there's no need to plan a specific layout.\u003c\/p\u003e\u003ch4\u003eHow many probes can I run in total with the expander fitted?\u003c\/h4\u003e\u003cp\u003eUp to seven ReefSense probes and sensors across a ReefControl Pro with the expander connected.\u003c\/p\u003e","brand":"RedSea","offers":[{"title":"Default Title","offer_id":55242223583523,"sku":"BA9032","price":120.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0972\/7236\/5347\/files\/reefcontrol-reefsense-port-e-10268546564387-1-dq.webp?v=1790372841"},{"product_id":"reefcontrol-pro","title":"ReefControl Pro","description":"\u003cp\u003e\u003cstrong\u003eOne hub, up to seven probes, and the readings you can trust while you're at work.\u003c\/strong\u003e The Red Sea ReefControl Pro is the flagship monitoring and automation controller in Red Sea's ReefBeat ecosystem. It ships ready to read pH and temperature straight out of the box, with three more built-in ReefSense ports free for salinity, ORP or a second temperature probe as you add them — and an optional expander to take the total to seven. Everything you need to check or adjust is one tap away in the ReefBeat app, from anywhere with internet access.\u003c\/p\u003e\u003ch3\u003eWhat's included \/ what you'll still need\u003c\/h3\u003e\u003cp\u003eThe box contains the ReefControl Pro controller, one ReefSense pH \u0026amp; Temperature combined probe, a 4-port ReefSense connector cable (3 m), and a single probe holder. It does not include Salinity, ORP or Leak Detector probes — these are genuine ReefSense accessories, each sold separately, and you'll need the separate ReefSense 4-Port Expander if you want to run more than four probes at once. ReefControl Pro also does not switch mains-powered equipment on its own: it has two 12 V DC ports for small accessories such as cooling fans or DC dosing pumps, but pumps, heaters, lights and skimmers need the separate ReefControl Power unit to be switched through the app.\u003c\/p\u003e\u003ch3\u003eKey features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFour built-in ReefSense ports, expandable to seven\u003c\/strong\u003e — start with pH and temperature and add salinity, ORP or a second temperature probe as your setup grows.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRuns from the ReefBeat app\u003c\/strong\u003e — live readings, history, and alerts if a parameter drifts out of your set range, from any internet connection.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBluetooth-capable probe connections\u003c\/strong\u003e — probes can report wirelessly where the layout calls for it, not just by cable.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTwo 12 V DC device ports\u003c\/strong\u003e — power and switch small low-voltage accessories directly from the hub.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eReefSense ports\u003c\/th\u003e\n\u003ctd\u003e4 built-in, expandable to 7 with the ReefSense 4-Port Expander (sold separately)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eIncluded probe\u003c\/th\u003e\n\u003ctd\u003e1x ReefSense pH \u0026amp; Temperature combined probe\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDC device ports\u003c\/th\u003e\n\u003ctd\u003e2x 12 V DC, for low-voltage accessories only\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAC equipment control\u003c\/th\u003e\n\u003ctd\u003eNot built in — requires the separate ReefControl Power unit\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApp\u003c\/th\u003e\n\u003ctd\u003eReefBeat (iOS and Android)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003epH accuracy\u003c\/th\u003e\n\u003ctd\u003e±0.05 pH, 0.01 pH precision\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTemperature accuracy\u003c\/th\u003e\n\u003ctd\u003e±0.05°C (combined probe), ±0.1°C (standalone probe)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSalinity accuracy\u003c\/th\u003e\n\u003ctd\u003e±1%\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eORP accuracy\u003c\/th\u003e\n\u003ctd\u003e±30 mV, 1 mV precision\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePart number\u003c\/th\u003e\n\u003ctd\u003eR35813 (Red Sea)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePower supply\u003c\/th\u003e\n\u003ctd\u003e12 V DC, 3.33 A (40 W max); mains input 100–240 V AC, 50\/60 Hz — works on Australian 230 V supply\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhich ReefControl do I need?\u003c\/h3\u003e\u003cp\u003eReefControl Pro is the full monitoring hub with expandable ports and the accuracy figures above. If you only need to switch outlets on and off — no probes — the separate ReefControl Power range does that job without the controller. If you want a fuller probe set from day one rather than adding them over time, the ReefControl Pro Deluxe Kit bundles the Pro with additional ReefSense probes.\u003c\/p\u003e\u003ch3\u003eSuitable for, and not suitable for\u003c\/h3\u003e\u003cp\u003eSuitable for freshwater and marine aquarists who want centralised, app-based monitoring and are happy to add probes as their setup grows. Not a complete automation solution by itself — mains-powered equipment still needs a ReefControl Power unit to be switched through the app, and probes beyond pH\/temperature are bought separately.\u003c\/p\u003e\u003ch3\u003eWarranty and delivery\u003c\/h3\u003e\u003cp\u003eCovered by Red Sea's manufacturer warranty, in addition to your consumer guarantee rights under Australian Consumer Law. Red Sea's published warranty term for ReefControl Pro is 24 months from the date of original purchase. Ships as a standard parcel item.\u003c\/p\u003e\u003ch3\u003eCommon questions\u003c\/h3\u003e\u003ch4\u003eCan it turn my heater or return pump on and off?\u003c\/h4\u003e\u003cp\u003eNot by itself. ReefControl Pro reads probes and runs the ReefBeat app; switching mains-powered equipment needs a separate ReefControl Power unit connected to it.\u003c\/p\u003e\u003ch4\u003eDo I need to buy probes separately?\u003c\/h4\u003e\u003cp\u003eOnly the pH \u0026amp; Temperature probe is included. Salinity, ORP and the Leak Detector are each sold separately as genuine ReefSense accessories.\u003c\/p\u003e\u003ch4\u003eHow many probes can I run at once?\u003c\/h4\u003e\u003cp\u003eFour, straight out of the box. Add the ReefSense 4-Port Expander (sold separately) to run up to seven.\u003c\/p\u003e\u003ch4\u003eIs it suitable for freshwater tanks?\u003c\/h4\u003e\u003cp\u003eThe hub and app work with any tank; which probes make sense depends on what you're monitoring — pH and temperature suit both fresh and marine setups, while salinity is a saltwater-specific parameter.\u003c\/p\u003e\n","brand":"RedSea","offers":[{"title":"Default Title","offer_id":55242228171043,"sku":"BA9019","price":810.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0972\/7236\/5347\/files\/reefcontrol-pro-10268548202787-1-dq.webp?v=1790372840"},{"product_id":"reefcontrol-pro-dlx-kit","title":"ReefControl Pro DLX Kit","description":"\u003cp\u003e\u003cstrong\u003eA Red Sea reef controller with three probes and a leak detector in the box.\u003c\/strong\u003e The ReefControl Pro Deluxe Kit pairs the ReefControl Pro controller with ReefSense digital probes for pH and temperature, salinity and temperature, and ORP (oxidation reduction potential, a general indicator of water quality), plus a ReefSense leak detector. You read the probes, calibrate them and set alerts and automations in Red Sea's ReefBeat app.\u003c\/p\u003e\n\u003ch3\u003eKey features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eDigital ReefSense probes\u003c\/strong\u003e plug into any free port on the controller, rather than each probe type needing its own dedicated port.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFour probe ports\u003c\/strong\u003e on the controller, expandable to seven ReefSense probes and sensors in total with the ReefSense Port Expander.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTwo 12 V DC outlets\u003c\/strong\u003e on the controller for switching low voltage equipment.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReefBeat app\u003c\/strong\u003e for probe readings, calibration, parameter logs, notifications and automations.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWorks with ReefControl Power\u003c\/strong\u003e (sold separately) to switch mains powered equipment, and the leak detector is compatible with Red Sea's ReefATO+ auto top off.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eIn the box: ReefControl Pro controller, ReefSense pH and temperature probe, ReefSense salinity and temperature probe, ReefSense ORP probe, ReefSense leak detector, three single probe holders, power supply\u003c\/li\u003e\n\u003cli\u003eProbe ports: 4 on the controller, up to 7 probes and sensors in total\u003c\/li\u003e\n\u003cli\u003eOutlets: two 12 V DC\u003c\/li\u003e\n\u003cli\u003eApp: Red Sea ReefBeat\u003c\/li\u003e\n\u003cli\u003eStore SKU: BA9020\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSuitable for, and not suitable for\u003c\/h3\u003e\n\u003cp\u003eSuitable for marine and reef aquariums where you want round the clock monitoring of pH, salinity, temperature and ORP with alerts on your phone, and for tanks already running other Red Sea ReefBeat equipment. It does not measure alkalinity, calcium, magnesium or nutrients, so you still need test kits for those.\u003c\/p\u003e\n\u003ch3\u003eCare\u003c\/h3\u003e\n\u003cp\u003eCalibrate the probes through the ReefBeat app as Red Sea's instructions set out, and keep probe tips clean.\u003c\/p\u003e\n\u003ch3\u003eSafety\u003c\/h3\u003e\n\u003cp\u003eMount the controller and power supply where they cannot be splashed, and plug into an RCD (safety switch) protected outlet.\u003c\/p\u003e\n\u003ch3\u003eWarranty and delivery\u003c\/h3\u003e\n\u003cp\u003eYour rights under Australian Consumer Law apply. Ships by standard parcel post.\u003c\/p\u003e","brand":"RedSea","offers":[{"title":"Default Title","offer_id":55242228203811,"sku":"BA9020","price":1225.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0972\/7236\/5347\/files\/reefcontrol-pro-dlx-kit-10268548235555-1-dq.webp?v=1790372840"},{"product_id":"reefcontrol-lite","title":"ReefControl Lite","description":"\u003cp\u003e\u003cstrong\u003eReef monitoring without the price tag of a full controller.\u003c\/strong\u003e The Red Sea ReefControl Lite is the entry point into Red Sea's ReefBeat ecosystem: a two-port monitoring hub that reads pH, temperature and one other parameter of your choice, runs a 12V accessory outlet, and puts live readings, alerts and automation history on your phone. It suits a reef or marine keeper who wants proper monitoring and alerting without committing to a full-scale controller and multiple probes on day one.\u003c\/p\u003e\u003ch3\u003eKey features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eTwo ReefSense probe ports\u003c\/strong\u003e — universal ports that accept any ReefSense probe, so you choose what to monitor rather than being locked to fixed inputs.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003epH and temperature probe included\u003c\/strong\u003e — the second port is free for a salinity, ORP or leak-detection probe as your system grows.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOne 12V DC outlet\u003c\/strong\u003e — runs a cooling fan, solenoid or small utility pump, switched from the app.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReefBeat app control\u003c\/strong\u003e — live readings, calibration, alerts and logging from your phone, with Bluetooth used for probe calibration and Wi-Fi for the live app connection.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eExpandable\u003c\/strong\u003e — a genuine first step into the ReefControl range rather than a dead end; add ReefSense probes as your monitoring needs grow.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eReefSense probe ports\u003c\/th\u003e\n\u003ctd\u003e2\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProbe included\u003c\/th\u003e\n\u003ctd\u003epH \u0026amp; temperature\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003e12V DC outlet\u003c\/th\u003e\n\u003ctd\u003e1, app-controlled\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eConnectivity\u003c\/th\u003e\n\u003ctd\u003eWi-Fi (ReefBeat app), Bluetooth (probe calibration)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApp\u003c\/th\u003e\n\u003ctd\u003eReefBeat\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWater type\u003c\/th\u003e\n\u003ctd\u003eMarine \/ reef\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePower supply\u003c\/th\u003e\n\u003ctd\u003e12 V DC, 1.75 A (21 W max); mains input 100–240 V AC, 50\/60 Hz — works on Australian 230 V supply\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat's included\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eReefControl Lite controller with 2-port connector cable\u003c\/li\u003e\n\u003cli\u003eReefSense pH \u0026amp; temperature probe\u003c\/li\u003e\n\u003cli\u003eSingle probe holder\u003c\/li\u003e\n\u003cli\u003epH 7 and pH 10 calibration solutions with vials\u003c\/li\u003e\n\u003cli\u003eMounting bracket and sump\/wall brackets\u003c\/li\u003e\n\u003cli\u003e12V power supply\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eNot included\u003c\/h3\u003e\u003cp\u003eReefControl Lite monitors and reads, but it does not switch mains-powered equipment on its own — for that, pair it with a ReefControl Power unit. It also doesn't ship with any probe beyond pH and temperature; salinity, ORP and leak-detection probes are sold separately.\u003c\/p\u003e\u003ch3\u003eWhich ReefControl do I need?\u003c\/h3\u003e\u003cp\u003eReefControl Lite covers two probes and a single 12V outlet — enough for most home reef tanks wanting core monitoring and alerts. If you're planning to run several ReefSense probes at once, or want the controller itself to switch your mains-powered equipment rather than just monitor it, ask us about the full ReefControl Pro hub and a ReefControl Power unit instead.\u003c\/p\u003e\u003ch3\u003eSuitable for, and not suitable for\u003c\/h3\u003e\u003cp\u003eSuitable for a reef or marine tank that wants reliable pH and temperature monitoring with room to add a second probe later. Not the right choice if you need the controller to directly switch multiple pieces of equipment — that job belongs to ReefControl Power, run alongside or instead of the Lite.\u003c\/p\u003e\u003ch3\u003eGoes well with\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eReefControl Power 6\u003c\/strong\u003e — lets the same ecosystem switch mains-powered equipment, not just monitor it.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAdditional ReefSense salinity or ORP probe\u003c\/strong\u003e — fills the Lite's second port.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReefControl Grounding Probe\u003c\/strong\u003e — pairs with a ReefControl Power unit to reduce stray voltage affecting probe readings.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWarranty and delivery\u003c\/h3\u003e\u003cp\u003eCovered by Red Sea's manufacturer warranty, in addition to your consumer guarantee rights under Australian Consumer Law. Standard parcel delivery.\u003c\/p\u003e\u003ch3\u003eCommon questions\u003c\/h3\u003e\u003ch4\u003eCan it run without Wi-Fi?\u003c\/h4\u003e\u003cp\u003eIt needs a Wi-Fi connection for live app monitoring, alerts and remote access through ReefBeat. Probe calibration uses Bluetooth and can be done without a home network.\u003c\/p\u003e\u003ch4\u003eCan I add more than two probes later?\u003c\/h4\u003e\u003cp\u003eReefControl Lite is limited to its two built-in ports. If you need more simultaneous probes, the full ReefControl Pro hub supports expansion beyond that.\u003c\/p\u003e\u003ch4\u003eDoes it switch my heater or pump on and off?\u003c\/h4\u003e\u003cp\u003eNot on its own — ReefControl Lite reads and alerts. To switch mains-powered equipment automatically, pair it with a ReefControl Power unit.\u003c\/p\u003e\u003ch4\u003eWhat's the difference between ReefControl Lite and ReefControl Pro?\u003c\/h4\u003e\u003cp\u003eLite is capped at two ReefSense probes and one 12V outlet, aimed at core monitoring. Pro supports more probes and deeper automation for larger or more heavily instrumented systems.\u003c\/p\u003e\n","brand":"RedSea","offers":[{"title":"Default Title","offer_id":55242228236579,"sku":"BA9018","price":585.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0972\/7236\/5347\/files\/reefcontrol-lite-10268548268323-1-dq.webp?v=1790372840"},{"product_id":"reefcontrol-power-6-deluxe","title":"ReefControl Power 6 Deluxe","description":"\u003cp\u003e\u003cstrong\u003eThe same six outlets, with physical switches at the unit.\u003c\/strong\u003e The Red Sea ReefControl Power 6 Deluxe is the standard ReefControl Power 6 with a manual control panel added: backlit on\/off pushbuttons for each of the six outlets, plus a master switch, alongside the same 2,400W Australian rating and full ReefBeat app control. It suits anyone who wants app scheduling day to day but doesn't want to reach for a phone every time they need to kill power to a pump.\u003c\/p\u003e\u003ch3\u003eKey features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e6 individually controllable outlets\u003c\/strong\u003e — 2,400W combined rating on the Australian 240V unit.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eManual control panel\u003c\/strong\u003e — backlit on\/off pushbutton for every outlet, plus a master switch for all six together.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePer-outlet power monitoring\u003c\/strong\u003e — spot a device drawing more or less than usual before it fails.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFeed mode and night mode\u003c\/strong\u003e — pause pumps and skimmers, or step lighting down, on a schedule or with one tap.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDirect temperature probe input\u003c\/strong\u003e — heater backup and failure alerts independent of your main controller.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eGrounding probe port\u003c\/strong\u003e — dedicated socket for the Red Sea ReefControl Grounding Probe, sold separately.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eOutlets\u003c\/th\u003e\n\u003ctd\u003e6, individually controllable\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTotal power rating (AU 240V model)\u003c\/th\u003e\n\u003ctd\u003e2,400W\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDimensions (L x W x H)\u003c\/th\u003e\n\u003ctd\u003e41 x 8.5 x 7.7 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eManual control panel\u003c\/th\u003e\n\u003ctd\u003eBacklit pushbutton per outlet, plus master switch\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eConnectivity\u003c\/th\u003e\n\u003ctd\u003eWi-Fi via ReefBeat app\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eGrounding probe port\u003c\/th\u003e\n\u003ctd\u003eYes, probe sold separately\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApp\u003c\/th\u003e\n\u003ctd\u003eReefBeat\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003ch3\u003eWhat's included\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eReefControl Power 6 Deluxe unit with 6 mains outlets\u003c\/li\u003e\n\u003cli\u003eManual control panel with backlit pushbuttons and master switch\u003c\/li\u003e\n\u003cli\u003eWi-Fi connectivity for ReefBeat app control\u003c\/li\u003e\n\u003cli\u003eTemperature probe input\u003c\/li\u003e\n\u003cli\u003eGrounding probe port (probe sold separately)\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWhich ReefControl Power do I need?\u003c\/h3\u003e\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003e\u003c\/th\u003e\n\u003cth\u003eReefControl Power 6\u003c\/th\u003e\n\u003cth\u003eReefControl Power 6 Deluxe\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eOutlets\u003c\/th\u003e\n\u003ctd\u003e6\u003c\/td\u003e\n\u003ctd\u003e6\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eTotal power (AU)\u003c\/th\u003e\n\u003ctd\u003e2,400W\u003c\/td\u003e\n\u003ctd\u003e2,400W\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApp control\u003c\/th\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003ctd\u003eYes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eManual control panel\u003c\/th\u003e\n\u003ctd\u003eNo\u003c\/td\u003e\n\u003ctd\u003eYes — backlit on\/off pushbutton per outlet, plus a master switch\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\u003cp\u003eThe Deluxe costs more for the same switching capacity and the same 2,400W rating — the difference is entirely the physical control panel. If your Wi-Fi is reliable and you're happy running everything from ReefBeat, the standard Power 6 does the same job for less.\u003c\/p\u003e\u003ch3\u003eSuitable for, and not suitable for\u003c\/h3\u003e\u003cp\u003eSuitable for anyone who wants app control day to day but also wants a physical switch on hand — during a Wi-Fi outage, for a quick manual override, or simply because a visible switch is reassuring on equipment that's keeping livestock alive. Not worth the premium if you're comfortable relying on the app alone; the standard Power 6 is functionally identical otherwise.\u003c\/p\u003e\u003ch3\u003eSafety\u003c\/h3\u003e\u003cp\u003eRun on an RCD-protected circuit. Keep drip loops on every cable entering or leaving the unit, and mount it above likely water level. Total load across all six outlets should stay within the 2,400W AU rating regardless of whether you're switching via the app or the panel.\u003c\/p\u003e\u003ch3\u003eGoes well with\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eReefControl Lite\u003c\/strong\u003e — adds probe monitoring alongside the Power unit's switching.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReefControl Grounding Probe\u003c\/strong\u003e — plugs into the dedicated port to reduce stray voltage.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eReefControl Power 6\u003c\/strong\u003e — the same unit without the manual panel, if app-only control is enough.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWarranty and delivery\u003c\/h3\u003e\u003cp\u003eCovered by Red Sea's manufacturer warranty, in addition to your consumer guarantee rights under Australian Consumer Law. Standard parcel delivery.\u003c\/p\u003e\u003ch3\u003eCommon questions\u003c\/h3\u003e\u003ch4\u003eWhat does the Deluxe add over the standard Power 6?\u003c\/h4\u003e\u003cp\u003eA manual control panel — backlit on\/off pushbuttons for each of the six outlets and a master switch — on top of the same 2,400W AU rating and ReefBeat app control.\u003c\/p\u003e\u003ch4\u003eCan I still use the app if I have the manual panel?\u003c\/h4\u003e\u003cp\u003eYes, both work together. The panel gives you a physical override; scheduling, monitoring and automation still run through ReefBeat.\u003c\/p\u003e\u003ch4\u003eDoes the manual panel work without Wi-Fi?\u003c\/h4\u003e\u003cp\u003eYes — the physical pushbuttons switch outlets locally and don't depend on a Wi-Fi connection, unlike scheduling and remote control through the app.\u003c\/p\u003e\u003ch4\u003eDo I need the grounding probe with this unit?\u003c\/h4\u003e\u003cp\u003eNo, it's optional, and connects via a dedicated port on the unit whether you have the standard or Deluxe version.\u003c\/p\u003e","brand":"RedSea","offers":[{"title":"Default Title","offer_id":55242228269347,"sku":"BA9021","price":695.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0972\/7236\/5347\/files\/reefcontrol-power-6-deluxe-43138106687779.webp?v=1790230923"},{"product_id":"auto-aqua-dc-solenoid-valve","title":"Auto Aqua DC Solenoid Valve","description":"\u003cp\u003e\u003cstrong\u003eFeeds top-off water straight from the RO line, with no refill pump to fail.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe AutoAqua DC Solenoid Valve (SV-12V) replaces the submersible refill pump on an AutoAqua top-off or water-change controller. When the controller calls for water, the valve opens and pressurised RO water flows directly into the tank or sump. It runs on 6 W at 12 V DC taken from the controller's pump socket, joins the line with quarter-inch push-fit RO tubing, and operates on any supply between 0.02 and 0.7 MPa. It suits reef and freshwater keepers who already make their own RO water and want the top-off reservoir out of the cabinet entirely.\u003c\/p\u003e\n\n\u003ch3\u003eKey features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eRuns off the controller's pump socket\u003c\/strong\u003e — 6 W at 12 V DC through a 5.5 x 2.5 mm plug, so there is no second power supply competing for an outlet.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDirect feed instead of a reservoir\u003c\/strong\u003e — water comes from the pressurised RO line, so there is no drum to refill and no submerged pump sitting in it.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eQuarter-inch push-connect\u003c\/strong\u003e — the same tubing standard as every RO\/DI unit, so it drops into an existing line.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWide operating window\u003c\/strong\u003e — 0.02 to 0.7 MPa covers household mains pressure and a gravity-fed drum mounted high enough.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e120 cm valve lead\u003c\/strong\u003e — reaches from a controller in the cabinet to a line entering at the back.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNothing in the water\u003c\/strong\u003e — no impeller to scale up, block or wear out.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003ePower\u003c\/th\u003e\n\u003ctd\u003e6 W at 12 V DC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePower source\u003c\/th\u003e\n\u003ctd\u003eHost AutoAqua controller's pump socket — no separate adaptor supplied\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDC connector\u003c\/th\u003e\n\u003ctd\u003e5.5 x 2.5 mm male\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eValve cable length\u003c\/th\u003e\n\u003ctd\u003e120 cm (4 ft)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWorking pressure\u003c\/th\u003e\n\u003ctd\u003e0.02 to 0.7 MPa (0.2 to 7 bar)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWater connection\u003c\/th\u003e\n\u003ctd\u003eQuarter-inch push-connect RO tubing\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWater carried\u003c\/th\u003e\n\u003ctd\u003eFiltered RO or RO\/DI water only\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003eAutoAqua top-off and water-change systems that use a submersible refill pump\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eManufacturer part number\u003c\/th\u003e\n\u003ctd\u003eSV-12V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\n\u003ch3\u003eFeed pressure — will it open on my line?\u003c\/h3\u003e\n\u003cp\u003eA solenoid valve does not pull water. It only lets through what is already pushing on it, which makes feed pressure the specification that decides whether it works in your setup.\u003c\/p\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSupply arrangement\u003c\/th\u003e\n\u003cth\u003ePressure at the valve\u003c\/th\u003e\n\u003cth\u003eResult\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eMains-pressure RO line\u003c\/td\u003e\n\u003ctd\u003eWithin 0.02 to 0.7 MPa\u003c\/td\u003e\n\u003ctd\u003eOpens and flows normally\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eGravity feed, reservoir at least 200 cm above the valve\u003c\/td\u003e\n\u003ctd\u003eAbout 0.02 MPa\u003c\/td\u003e\n\u003ctd\u003eThe minimum head AutoAqua specifies for a gravity feed\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eGravity feed, reservoir less than 200 cm above the valve\u003c\/td\u003e\n\u003ctd\u003eBelow 0.02 MPa\u003c\/td\u003e\n\u003ctd\u003eBelow the stated minimum — the valve may not open reliably\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHigh-pressure line\u003c\/td\u003e\n\u003ctd\u003eAbove 0.7 MPa\u003c\/td\u003e\n\u003ctd\u003eAbove the stated maximum — fit a pressure regulator upstream\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eFitting it safely\u003c\/h3\u003e\n\u003cp\u003eAutoAqua is explicit on two points, and both are worth reading before you cut any tubing.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eA mechanical float valve is mandatory.\u003c\/strong\u003e Where this solenoid is used with a top-off or water-change system, AutoAqua requires a mechanical float valve fitted as a fail-safe. Electronics that fail closed are harmless; electronics that fail open put the contents of your RO line on the floor.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eFiltered water only.\u003c\/strong\u003e AutoAqua restricts the valve to filtered water. Raw tap water and saltwater will clog it.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhat's included\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eDC solenoid valve with a 120 cm lead and 5.5 x 2.5 mm DC plug\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eNot included\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eA 12 V power supply — the valve is powered by the AutoAqua controller it plugs into\u003c\/li\u003e\n\u003cli\u003eThe top-off or water-change controller itself\u003c\/li\u003e\n\u003cli\u003eQuarter-inch RO tubing\u003c\/li\u003e\n\u003cli\u003eA mechanical float valve, which AutoAqua requires as a fail-safe\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eSuitable for, and not suitable for\u003c\/h3\u003e\n\u003cp\u003eSuitable for:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eAutoAqua top-off and water-change systems that currently use a submersible refill pump\u003c\/li\u003e\n\u003cli\u003eFreshwater and marine tanks fed from an RO or RO\/DI unit\u003c\/li\u003e\n\u003cli\u003eSetups where you would rather not keep a top-off reservoir in the cabinet\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNot suitable for:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eUnfiltered tap water or saltwater — AutoAqua restricts it to filtered water\u003c\/li\u003e\n\u003cli\u003eLines below 0.02 MPa, including a gravity feed with less than 200 cm of height above the valve\u003c\/li\u003e\n\u003cli\u003eLines above 0.7 MPa without a pressure regulator\u003c\/li\u003e\n\u003cli\u003eStandalone use — it needs a 12 V DC source and a controller to switch it\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCare and maintenance\u003c\/h3\u003e\n\u003cp\u003eKeep the valve body dry and out of splash range. If flow drops away, check feed pressure at the valve before assuming the solenoid has failed — pressure is the more common cause. Check that the fail-safe float valve still seats freely each time you service the RO unit.\u003c\/p\u003e\n\n\u003ch3\u003eGoes well with\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/autoaqua-smart-ato-duo\"\u003eAutoAqua Smart ATO Duo\u003c\/a\u003e — a top-off controller this valve can replace the refill pump on\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/autoaqua-smart-ato-ro-auto-top-for-ro-system\"\u003eAutoAqua Smart ATO RO\u003c\/a\u003e — the RO-fed top-off unit in the same range\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/red-sea-max-e-s-reefer-ato-float-valve\"\u003eRed Sea ATO float valve\u003c\/a\u003e — a mechanical float valve for the fail-safe AutoAqua requires\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/auto-aqua-digital-inline-tds-titanium-s1\"\u003eAutoAqua Digital Inline TDS Titanium S1\u003c\/a\u003e — confirms the water going through the valve is still clean\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/reef-pure-4-stage-eddentials\"\u003eReef Pure 4 Stage Essentials+\u003c\/a\u003e — an RO\/DI unit to supply the line\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/autoaqua\"\u003eThe full AutoAqua range\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWarranty and delivery\u003c\/h3\u003e\n\u003cp\u003eShips as a standard parcel. Any manufacturer's warranty offered on this valve applies in addition to the consumer guarantees you have under Australian Consumer Law, which cannot be excluded.\u003c\/p\u003e\n\n\u003ch3\u003eCommon questions\u003c\/h3\u003e\n\u003ch4\u003eDoes the AutoAqua DC Solenoid Valve need its own power supply?\u003c\/h4\u003e\n\u003cp\u003eNo. The AutoAqua DC Solenoid Valve draws 6 W at 12 V DC through a 5.5 x 2.5 mm plug, which connects to the pump socket on the AutoAqua controller running it. No separate adaptor is supplied or required.\u003c\/p\u003e\n\u003ch4\u003eCan I run tap water or saltwater through it?\u003c\/h4\u003e\n\u003cp\u003eNo. AutoAqua specifies filtered water only for this valve. Raw tap water and saltwater will clog it.\u003c\/p\u003e\n\u003ch4\u003eDo I still need a mechanical float valve?\u003c\/h4\u003e\n\u003cp\u003eYes. AutoAqua requires a mechanical float valve as a fail-safe whenever this solenoid is used with a top-off or water-change system.\u003c\/p\u003e\n\u003ch4\u003eHow much pressure does the valve need to open?\u003c\/h4\u003e\n\u003cp\u003eBetween 0.02 and 0.7 MPa. If you are feeding by gravity rather than mains pressure, AutoAqua specifies at least 200 cm of height between the reservoir and the valve.\u003c\/p\u003e\n\u003ch4\u003eWhich AutoAqua units does it fit?\u003c\/h4\u003e\n\u003cp\u003eAutoAqua lists it as compatible with its top-off and water-change systems that use a submersible refill pump, where it takes the place of that pump.\u003c\/p\u003e","brand":"AutoAqua","offers":[{"title":"Default Title","offer_id":55242230432035,"sku":"BA8859","price":59.95,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0972\/7236\/5347\/files\/auto-aqua-dc-solenoid-valve-43508248248611.webp?v=1790234084"},{"product_id":"auto-aqua-smart-smart-level-security","title":"AutoAqua Smart Level Security","description":"\u003cp\u003e\u003cstrong\u003eCuts the power to one piece of equipment when the water goes where it should not.\u003c\/strong\u003e The AutoAqua Smart Level Security (model SLS-120, EU\/UK\/AU version) is a water level alarm with its own switched power point, called the Smart AC Switch. An optical sensor (it detects water using light rather than a float) mounts magnetically on the tank or sump. When it is triggered, the unit shuts off the equipment plugged into the AC Switch and sounds an audible and visual alarm straight away.\u003c\/p\u003e\u003ch3\u003eKey features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eHigh level or low level\u003c\/strong\u003e: mount the sensor above the water line to catch an overflow, or below it to catch a falling level. There is nothing to set.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eShuts off and alarms together\u003c\/strong\u003e, so the fault stops instead of only making a noise.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMagnetic mount\u003c\/strong\u003e that works on clear, tinted or painted surfaces up to 12.7 mm thick.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAuto time delay\u003c\/strong\u003e to avoid false alarms after a power outage. AutoAqua's manual gives a 2 minute power on delay and a 2 minute detection delay.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePlug and play\u003c\/strong\u003e: mount the sensor, plug your equipment into the AC Switch, then plug the AC Switch in.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eModel: SLS-120, EU\/UK\/AU version\u003c\/li\u003e\n\u003cli\u003ePower input and output: 100 to 240 V AC, 10 A\u003c\/li\u003e\n\u003cli\u003eMaximum load: 2200 W at 220 V AC\u003c\/li\u003e\n\u003cli\u003eMaximum mounting thickness: 12.7 mm (1\/2 inch)\u003c\/li\u003e\n\u003cli\u003eSensor cable length: 300 cm (10 feet)\u003c\/li\u003e\n\u003cli\u003eAlarm: flashing red light with an audible alarm\u003c\/li\u003e\n\u003cli\u003eIncluded: Smart Level Security unit, world plug type adapter\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSuitable for, and not suitable for\u003c\/h3\u003e\u003cp\u003eSuitable as an independent flood cut-off for an auto top-off (a unit that tops up evaporated water), or as a low level cut-off to stop a return pump running dry when a sump level falls. Not suitable for loads over 10 A or 2200 W, for panels thicker than 12.7 mm, or for sensor positions with microbubbles or direct light on the sensor, which AutoAqua says to avoid. It protects one device at a time and is not a replacement for an RCD (safety switch).\u003c\/p\u003e\u003ch3\u003eCare\u003c\/h3\u003e\u003cp\u003eWhen the alarm goes off, unplug the AC Switch first, then find and fix the cause before plugging it back in. Test the sensor from time to time by moving it into or out of the water by hand and checking the equipment switches off.\u003c\/p\u003e\u003ch3\u003eSafety\u003c\/h3\u003e\u003cp\u003eKeep the AC Switch dry and above splash height, use a drip loop (a downward loop in each cord so water runs off before the plug) and run the aquarium circuit through an RCD.\u003c\/p\u003e\u003ch3\u003eWarranty and delivery\u003c\/h3\u003e\u003cp\u003eAutoAqua's SLS-120 manual gives a two year warranty from the purchase date, under proper installation and normal use, with proof of purchase, in addition to your rights under Australian Consumer Law. Ships by standard parcel post.\u003c\/p\u003e","brand":"AutoAqua","offers":[{"title":"Default Title","offer_id":55242234102051,"sku":"BA7916","price":109.95,"currency_code":"AUD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0972\/7236\/5347\/files\/auto-aqua-smart-smart-level-43106844606755.webp?v=1790230925"},{"product_id":"auto-aqua-smart-temp-security","title":"Auto Aqua Smart Temp Security","description":"\u003cp\u003e\u003cstrong\u003eCuts power to a stuck heater before it cooks the tank.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe AutoAqua Smart Temp Security is an independent temperature cut-off that sits between the wall and your heater or chiller. A magnet-mounted probe watches the water, and if the temperature leaves a fixed window of 22.2 to 28.8 °C the unit disconnects its outlet and alarms. It is rated to 10 A, needs no programming, and has an automatic delay so a brief interruption does not trip it. The window is not adjustable, and that single fact decides whether it suits your tank.\u003c\/p\u003e\n\n\u003ch3\u003eWhat it does, and what it does not do\u003c\/h3\u003e\n\u003cp\u003eThis is a safety device, not a temperature controller. There is no set point to choose and it will not hold your tank at a temperature.\u003c\/p\u003e\n\u003cp\u003eIt watches for the two failures that empty a tank overnight: a heater whose thermostat has welded closed, and a heater or chiller that has stopped working. When the water leaves the safe window, it removes power from whatever is plugged into it and sounds an alarm.\u003c\/p\u003e\n\u003cp\u003eYour heater keeps its own thermostat and still does the controlling. The Smart Temp Security only intervenes once that thermostat has already failed.\u003c\/p\u003e\n\n\u003ch3\u003eKey features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFixed 22.2 to 28.8 °C window\u003c\/strong\u003e — ±0.5 °C, with nothing to programme and nothing to mis-set at 11pm.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e10 A outlet\u003c\/strong\u003e — AutoAqua publishes 2200 W at 220 V AC, well above the draw of an aquarium heater.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAudible alarm\u003c\/strong\u003e — you learn the cut-off has fired from the unit, not from the livestock.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAutomatic time delay\u003c\/strong\u003e — rides out brief interruptions instead of nuisance-tripping after a blackout.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMagnetic probe\u003c\/strong\u003e — sticks on and repositions in seconds, no drilling and no suction cup to perish.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e300 cm sensor cable\u003c\/strong\u003e — reaches from a unit mounted clear of the water up to the display tank.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFunction\u003c\/th\u003e\n\u003ctd\u003eTemperature safety cut-off (not a controller)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCut-off window\u003c\/th\u003e\n\u003ctd\u003e22.2 to 28.8 °C (72 to 84 °F), fixed and not adjustable\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSensing tolerance\u003c\/th\u003e\n\u003ctd\u003e±0.5 °C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSupply\u003c\/th\u003e\n\u003ctd\u003e100 to 240 V AC, 50\/60 Hz\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eOutlet rating\u003c\/th\u003e\n\u003ctd\u003e10 A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaximum switched load\u003c\/th\u003e\n\u003ctd\u003e1100 W at 110 V AC; 2200 W at 220 V AC (AutoAqua published figures)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSensor\u003c\/th\u003e\n\u003ctd\u003eMagnetic temperature probe\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaximum sensor mounting thickness\u003c\/th\u003e\n\u003ctd\u003e12.7 mm (half an inch)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSensor cable length\u003c\/th\u003e\n\u003ctd\u003e300 cm (10 ft)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eProgramming\u003c\/th\u003e\n\u003ctd\u003eNone — plug and play\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\n\u003ch3\u003eThe cut-off window\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eWater temperature\u003c\/th\u003e\n\u003cth\u003eWhat the unit does\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eBelow 22.2 °C (72 °F)\u003c\/td\u003e\n\u003ctd\u003eDisconnects the outlet and alarms\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e22.2 to 28.8 °C (72 to 84 °F)\u003c\/td\u003e\n\u003ctd\u003eOutlet stays live; the heater or chiller runs on its own thermostat\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eAbove 28.8 °C (84 °F)\u003c\/td\u003e\n\u003ctd\u003eDisconnects the outlet and alarms\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eThose limits are fixed. Check them against the temperature you actually keep before you buy, not after.\u003c\/p\u003e\n\n\u003ch3\u003eWill it fit my tank?\u003c\/h3\u003e\n\u003cp\u003eTwo measurements decide it, and both are easy to check with a ruler.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMounting thickness\u003c\/strong\u003e — the probe magnet holds through material up to 12.7 mm. Glass, acrylic or cabinet panel thicker than that at the mounting point is outside the rating.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable reach\u003c\/strong\u003e — 300 cm between the probe and the unit, which needs to sit above splash height with access to a wall outlet.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eSuitable for, and not suitable for\u003c\/h3\u003e\n\u003cp\u003eSuitable for:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eTropical freshwater and marine tanks run inside 22.2 to 28.8 °C\u003c\/li\u003e\n\u003cli\u003eBacking up the heater on a reef or planted display\u003c\/li\u003e\n\u003cli\u003eAnyone who has lost stock to a stuck heater, or would rather not find out\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNot suitable for:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eColdwater tanks run below 22.2 °C — axolotls, cool-kept goldfish, temperate natives. The unit reads their normal running temperature as a fault and cuts the outlet\u003c\/li\u003e\n\u003cli\u003eTanks deliberately held above 28.8 °C, such as some discus and treatment setups\u003c\/li\u003e\n\u003cli\u003eLoads drawing more than 10 A\u003c\/li\u003e\n\u003cli\u003eGlass, acrylic or cabinet material thicker than 12.7 mm at the probe position\u003c\/li\u003e\n\u003cli\u003eUse as your only thermostat — it is a cut-off, not a controller\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhat's included\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eSmart Temp Security unit with switched mains outlet\u003c\/li\u003e\n\u003cli\u003eMagnetic temperature probe on a 300 cm cable\u003c\/li\u003e\n\u003cli\u003eUniversal plug-type power adaptor\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eNot included\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eHeater\u003c\/li\u003e\n\u003cli\u003eChiller\u003c\/li\u003e\n\u003cli\u003eAquarium thermometer for day-to-day reading\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eSafety and Australian electrical notes\u003c\/h3\u003e\n\u003cp\u003eThe unit is rated 100 to 240 V AC at 50\/60 Hz, which covers Australian 240 V \/ 50 Hz mains. Confirm the plug configuration supplied with your unit before installation, and have any adaptation done by a licensed electrician rather than improvised.\u003c\/p\u003e\n\u003cp\u003eMount the unit above splash height and clear of the sump. Test the cut-off before you rely on it by lifting the probe into water outside the window and confirming the outlet drops and the alarm sounds.\u003c\/p\u003e\n\n\u003ch3\u003eCare and maintenance\u003c\/h3\u003e\n\u003cp\u003eWipe the probe when you clean the glass, since a film of algae or salt creep slows its response. Re-test the cut-off after any tank move or rescape, and check the probe magnet has not crept down the panel.\u003c\/p\u003e\n\n\u003ch3\u003eGoes well with\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/bioscape-pro-electronic-heater\"\u003eBioscape PRO Electronic Heater\u003c\/a\u003e — the kind of heater this device is there to back up\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/teco-tk150-chiller\"\u003eTeco TK150 Chiller\u003c\/a\u003e — protected the same way at the top of the window\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/auto-aqua-smart-smart-level-security\"\u003eAutoAqua Smart Level Security\u003c\/a\u003e — the same idea applied to water level\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/autoaqua-smart-skimmer-securty-system\"\u003eAutoAqua Smart Skimmer Security System\u003c\/a\u003e — the same idea applied to skimmer overflow\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/fluval-digital-aquarium-thermometer\"\u003eFluval Digital Aquarium Thermometer\u003c\/a\u003e — for the everyday reading this device does not display\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/autoaqua\"\u003eThe full AutoAqua range\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWarranty and delivery\u003c\/h3\u003e\n\u003cp\u003eShips as a standard parcel. Any manufacturer's warranty offered on this unit applies in addition to the consumer guarantees you have under Australian Consumer Law, which cannot be excluded.\u003c\/p\u003e\n\n\u003ch3\u003eCommon questions\u003c\/h3\u003e\n\u003ch4\u003eCan I change the temperature the Smart Temp Security cuts out at?\u003c\/h4\u003e\n\u003cp\u003eNo. The AutoAqua Smart Temp Security uses a fixed window of 22.2 to 28.8 °C with ±0.5 °C tolerance. There is no adjustable set point.\u003c\/p\u003e\n\u003ch4\u003eDoes it replace my heater's thermostat?\u003c\/h4\u003e\n\u003cp\u003eNo. It is a cut-off that sits upstream of the heater. The heater keeps controlling temperature; the Smart Temp Security only removes power once the water has already left the safe window.\u003c\/p\u003e\n\u003ch4\u003eWill it work on an axolotl or coldwater tank?\u003c\/h4\u003e\n\u003cp\u003eNo. A tank run below 22.2 °C sits outside the fixed window, so the unit treats a perfectly normal running temperature as a fault and disconnects the outlet.\u003c\/p\u003e\n\u003ch4\u003eHow much can I plug into it?\u003c\/h4\u003e\n\u003cp\u003eThe outlet is rated 10 A. AutoAqua publishes a maximum switched load of 2200 W at 220 V AC and 1100 W at 110 V AC.\u003c\/p\u003e\n\u003ch4\u003eHow thick can the glass be where the probe mounts?\u003c\/h4\u003e\n\u003cp\u003eUp to 12.7 mm. The probe mounts magnetically and the cable between probe and unit is 300 cm.\u003c\/p\u003e\n\u003ch4\u003eDoes it need any setup or programming?\u003c\/h4\u003e\n\u003cp\u003eNo. It is plug and play, with an automatic time delay so a brief power interruption does not trip it unnecessarily.\u003c\/p\u003e","brand":"AutoAqua","offers":[{"title":"Default Title","offer_id":55242234134819,"sku":"BA7917","price":109.95,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0972\/7236\/5347\/files\/auto-aqua-smart-temp-securit-43106844639523.webp?v=1790230925"},{"product_id":"autoaqua-smart-skimmer-securty-system","title":"AutoAqua Smart Skimmer Security System","description":"\u003cp\u003e\u003cstrong\u003eCuts power to the skimmer before the cup overflows your cabinet.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe AutoAqua Smart Skimmer Security is a standalone overflow cut-off for a protein skimmer. An optical sensor clamps to the collection cup on a magnet, and the moment skimmate reaches it the unit kills mains power to the skimmer and sounds an alarm. It handles up to 10 amps — around 2,200 W on Australian 240 V mains — so it will switch any skimmer pump you are likely to own.\u003c\/p\u003e\n\n\u003ch3\u003eWhat actually goes wrong, and what this stops\u003c\/h3\u003e\n\u003cp\u003eA skimmer does not fail gradually. It runs correctly for weeks, then something shifts the bubble column — a dose of carbon, a water change, a feed, a slug of fresh top-off water — and the cup fills in under an hour.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eThe cup overflows, not the tank.\u003c\/strong\u003e Skimmate runs down the body, out the cup lid, and into the cabinet or across the sump. On a sump in a cabinet, the first sign is usually the smell.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNothing upstream notices.\u003c\/strong\u003e An ATO, a controller running a dosing schedule and a return pump all keep working normally while this happens. The skimmer is the only thing misbehaving.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIt happens on the days you are not there.\u003c\/strong\u003e Skimmers go unstable after the changes you make and then leave alone — which is the weekend and the night before a trip.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThe cost is not the skimmate.\u003c\/strong\u003e It is a litre or two of nutrient-dense waste back into the display, and a cabinet floor that stays wet.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eHow it behaves\u003c\/h3\u003e\n\u003cp\u003eThe unit sits between the wall socket and the skimmer pump. There is nothing to program.\u003c\/p\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eEvent\u003c\/th\u003e\n\u003cth\u003eWhat the unit does\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSkimmate reaches the optical sensor on the cup\u003c\/td\u003e\n\u003ctd\u003eCuts mains power to the skimmer, flashes red and sounds an audible alarm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eYou empty and refit the cup\u003c\/td\u003e\n\u003ctd\u003eAuto-recovery restores power without a manual reset\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMains power returns after an outage\u003c\/td\u003e\n\u003ctd\u003eA power-on delay holds the skimmer off before restarting it\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eA transient splash or bubble touches the sensor\u003c\/td\u003e\n\u003ctd\u003eA detection delay holds the trip, so a momentary wetting does not shut the skimmer down\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eThe delays are the part that matters in practice. An overflow sensor with no delay logic trips on froth and gets unplugged within a fortnight, which leaves you with no protection at all.\u003c\/p\u003e\n\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eSKU\u003c\/th\u003e\n\u003ctd\u003eAA2293\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBarcode\u003c\/th\u003e\n\u003ctd\u003e4714041212273\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFunction\u003c\/th\u003e\n\u003ctd\u003eProtein skimmer overflow cut-off with audible and visual alarm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSensor type\u003c\/th\u003e\n\u003ctd\u003eOptical, magnetically mounted to the collection cup\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMagnet size\u003c\/th\u003e\n\u003ctd\u003e20 mm diameter x 17 mm thick\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInput and output\u003c\/th\u003e\n\u003ctd\u003e100-240 V AC, 10 A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaximum switched load\u003c\/th\u003e\n\u003ctd\u003e2,200 W at 220 V AC (1,100 W at 110 V AC)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSensor cable length\u003c\/th\u003e\n\u003ctd\u003e3 m (10 ft)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eSetup\u003c\/th\u003e\n\u003ctd\u003ePlug-and-play, no programming, no controller required\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eRecovery\u003c\/th\u003e\n\u003ctd\u003eAutomatic once the cup is emptied\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWater type\u003c\/th\u003e\n\u003ctd\u003eMarine\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eWill it fit my skimmer?\u003c\/h3\u003e\n\u003cp\u003eFit is decided by the collection cup wall, not by the skimmer brand. The sensor is a two-part magnetic clamp: it grips through the cup wall, so the wall has to be thin enough for the magnets to hold.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eCup wall thickness\u003c\/strong\u003e is the limiting figure. AutoAqua publishes a maximum mounting thickness for the skimmer sensor of 8 mm on the current model. Most acrylic skimmer cups sit well under that.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCable reach\u003c\/strong\u003e is 3 m from the sensor back to the switch unit, which covers a sump skimmer and a socket outside the cabinet on almost any setup.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLoad\u003c\/strong\u003e is a non-issue. At 10 A the unit will switch any aquarium skimmer pump, DC or AC, with a very large margin.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSet the sensor height deliberately.\u003c\/strong\u003e Mount it near the top of the cup, not at the neck. Too low and you lose most of the cup's useful volume to nuisance trips.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhich AutoAqua Security unit do I need?\u003c\/h3\u003e\n\u003cp\u003eThe three Security units share the same switch body and the same delay logic. What differs is the sensor and the failure it watches for.\u003c\/p\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eUnit\u003c\/th\u003e\n\u003cth\u003eWatches\u003c\/th\u003e\n\u003cth\u003eTypical job\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSmart Skimmer Security — this page\u003c\/td\u003e\n\u003ctd\u003eSkimmate level in the collection cup\u003c\/td\u003e\n\u003ctd\u003eStops a skimmer overflowing into the cabinet or sump\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/auto-aqua-smart-smart-level-security\"\u003eAutoAqua Smart Level Security\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eWater level in the tank or sump\u003c\/td\u003e\n\u003ctd\u003eStops an overflow, or a pump running dry\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003e\u003ca href=\"\/products\/auto-aqua-smart-temp-security\"\u003eAutoAqua Smart Temp Security\u003c\/a\u003e\u003c\/td\u003e\n\u003ctd\u003eWater temperature\u003c\/td\u003e\n\u003ctd\u003eCuts a heater that has stuck on, or a chiller that has stuck off\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003eThey are independent devices, each with its own switched outlet. Running more than one is normal — they do not talk to each other and do not need a controller.\u003c\/p\u003e\n\n\u003ch3\u003eSuitable for, and not suitable for\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eSuitable for\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eAny marine setup where the skimmer sits in a cabinet or a sump room\u003c\/li\u003e\n\u003cli\u003eA new skimmer during its break-in weeks, when overflows are most likely\u003c\/li\u003e\n\u003cli\u003eReefers who dose carbon, bacteria or amino acids and see the skimmer react\u003c\/li\u003e\n\u003cli\u003eAnyone who travels and leaves the tank running unattended\u003c\/li\u003e\n\u003cli\u003eSkimmers without any built-in level control of their own\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eNot suitable for\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eControlling skimmer output or tuning the foam head — it is a cut-off, not a regulator\u003c\/li\u003e\n\u003cli\u003eTank water level or ATO duty — use the \u003ca href=\"\/products\/auto-aqua-smart-smart-level-security\"\u003eSmart Level Security\u003c\/a\u003e or an \u003ca href=\"\/products\/autoaqua-smart-ato-duo\"\u003eAutoAqua Smart ATO Duo\u003c\/a\u003e\n\u003c\/li\u003e\n\u003cli\u003eTemperature protection — use the \u003ca href=\"\/products\/auto-aqua-smart-temp-security\"\u003eSmart Temp Security\u003c\/a\u003e\n\u003c\/li\u003e\n\u003cli\u003eCup walls thicker than the published mounting limit, where the magnet cannot grip reliably\u003c\/li\u003e\n\u003cli\u003eReplacing a drain line or a sump with enough freeboard — this is a second line of defence, not the first\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eSafety\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eKeep the switch unit dry and above the water line.\u003c\/strong\u003e AutoAqua states this plainly in the manual. It is a mains switch, not a submersible device.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eRun it on an RCD-protected circuit\u003c\/strong\u003e and use a drip loop on every cable, as with all mains equipment near an aquarium.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTest it before you rely on it.\u003c\/strong\u003e Lift the sensor into wet skimmate by hand and confirm the skimmer cuts and the alarm sounds. Do this when the unit is new and again after any cup change.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDo not exceed 10 A\u003c\/strong\u003e on the switched outlet, and do not daisy-chain a powerboard of equipment through it. It is intended to switch the skimmer alone.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eClean the sensor face.\u003c\/strong\u003e Skimmate film on an optical sensor is the usual cause of a late trip.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCare and maintenance\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eWipe the sensor and the inside of the cup wall whenever you empty the cup — an optical sensor reads through the film that builds up on both.\u003c\/li\u003e\n\u003cli\u003eRe-test the trip after moving the sensor, changing skimmers, or swapping the collection cup.\u003c\/li\u003e\n\u003cli\u003eCheck the magnet grip after cleaning. Salt creep under a magnet foot lets the sensor slide down the cup over time.\u003c\/li\u003e\n\u003cli\u003eThere are no consumable parts and nothing to calibrate.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eGoes well with\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/auto-aqua-smart-temp-security\"\u003eAutoAqua Smart Temp Security\u003c\/a\u003e — covers the other overnight failure that empties a reef tank, a heater stuck on.\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/auto-aqua-smart-smart-level-security\"\u003eAutoAqua Smart Level Security\u003c\/a\u003e — sump and display level protection, the natural pair with skimmer protection on a sumped system.\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/autoaqua-smart-ato-duo\"\u003eAutoAqua Smart ATO Duo\u003c\/a\u003e — dual-sensor auto top-off, so top-off water arrives at a steady rate rather than in the slugs that upset a skimmer.\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/red-sea-reefer-skimmer-300-psk600\"\u003eRed Sea Reefer Skimmer 300 PSK600\u003c\/a\u003e — an in-sump skimmer this unit is well matched to.\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/aqua-medic-turboflotor-5000\"\u003eAqua Medic Turboflotor 5000\u003c\/a\u003e — a larger in-sump skimmer, comfortably inside the 10 A switching limit.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWarranty and delivery\u003c\/h3\u003e\n\u003cp\u003eAutoAqua does not publish a warranty term for the Smart Security range. Your rights under the Australian Consumer Law apply to this product and are not limited by any manufacturer's warranty.\u003c\/p\u003e\n\u003cp\u003eThe unit accepts 100-240 V AC, so it runs on Australian 230-240 V mains. Ships as a standard parcel.\u003c\/p\u003e\n\n\u003ch3\u003eCommon questions\u003c\/h3\u003e\n\u003ch4\u003eDoes the AutoAqua Smart Skimmer Security work with any brand of skimmer?\u003c\/h4\u003e\n\u003cp\u003eYes, provided two things are true. The collection cup wall must be within the published magnetic mounting thickness so the sensor can clamp to it, and the skimmer pump must draw under 10 amps, which every aquarium skimmer does. The unit switches mains power to the pump, so it is indifferent to the skimmer's brand, body design or whether the pump is AC or DC.\u003c\/p\u003e\n\u003ch4\u003eDo I have to reset it after the skimmer trips?\u003c\/h4\u003e\n\u003cp\u003eNo. The unit has an auto-recovery function: once you empty the collection cup and the sensor is clear, power is restored to the skimmer without pressing anything. A power-on delay holds the skimmer off briefly before it restarts.\u003c\/p\u003e\n\u003ch4\u003eWill it false-trip every time the foam surges?\u003c\/h4\u003e\n\u003cp\u003eIt is designed not to. AutoAqua builds a detection delay into the Smart Security range specifically so a momentary splash or a passing bubble does not shut equipment down, and a separate power-on delay so the skimmer does not restart into an unstable state straight after a blackout.\u003c\/p\u003e\n\u003ch4\u003eHow much power can it switch?\u003c\/h4\u003e\n\u003cp\u003eThe unit is rated 100-240 V AC at 10 amps, which AutoAqua states as 2,200 W at 220 V AC and 1,100 W at 110 V AC. On Australian mains that is roughly 2,200 W — far more than any aquarium skimmer pump requires. It should still be used to switch the skimmer alone rather than a powerboard of equipment.\u003c\/p\u003e\n\u003ch4\u003eHow long is the sensor cable?\u003c\/h4\u003e\n\u003cp\u003eThree metres, which AutoAqua also lists as 10 feet. That is enough to run from a skimmer cup in a sump, out of the cabinet, to a switch unit mounted dry near the power outlet.\u003c\/p\u003e\n\u003ch4\u003eIs this the same as an auto top-off controller?\u003c\/h4\u003e\n\u003cp\u003eNo. An ATO adds fresh water to replace evaporation. This unit only removes power from the skimmer when the collection cup fills. They protect against different failures and are commonly run together on the same system.\u003c\/p\u003e","brand":"AutoAqua","offers":[{"title":"Default Title","offer_id":55242245701923,"sku":"AA2293","price":119.95,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0972\/7236\/5347\/files\/autoaqua-smart-skimmer-secur-43106844836131.webp?v=1790231147"},{"product_id":"teco-nnect-wifi-devic","title":"Teco Nnect WiFi Device","description":"\u003cp\u003e\u003cstrong\u003eCheck on your chiller from wherever you are.\u003c\/strong\u003e The Teco Nnect is a plug-in WiFi module that connects a compatible Teco chiller to your home network, so you can monitor temperature, get alerts and adjust settings from the Teco app on your phone instead of walking over to the unit.\u003c\/p\u003e\n\u003ch3\u003eKey features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eRemote monitoring\u003c\/strong\u003e — check current tank temperature and chiller status from anywhere with a data or WiFi connection.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAlert notifications\u003c\/strong\u003e — configurable alarms push to your phone if temperature runs outside the range you set.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003ePerformance history\u003c\/strong\u003e — track how the chiller has been running over time, not just its current reading.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e°C\/°F toggle\u003c\/strong\u003e — switch display units in the app to suit you.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEasy install\u003c\/strong\u003e — plugs directly into a compatible chiller, no separate power supply.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eBrand\u003c\/th\u003e\n\u003ctd\u003eTeco\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eType\u003c\/th\u003e\n\u003ctd\u003eWiFi adapter module\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDimensions\u003c\/th\u003e\n\u003ctd\u003eApprox. 114 x 102 x 51mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eApp platforms\u003c\/th\u003e\n\u003ctd\u003eiOS and Android (Android 14+ not yet supported for initial pairing)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePower\u003c\/th\u003e\n\u003ctd\u003ePowered from the host chiller — no separate power supply needed\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eCompatibility\u003c\/h3\u003e\n\u003cp\u003eFits the current TK-500, TK-1000 and TK-2000 R290 chillers, which are WiFi-ready from the factory. It is not compatible with the older TK-150, which has no WiFi header to plug into.\u003c\/p\u003e\n\u003ch3\u003eSuitable for, and not suitable for\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eSuitable for:\u003c\/strong\u003e Teco TK-500, TK-1000 and TK-2000 R290 chillers where you want remote monitoring and alerts.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNot suitable for:\u003c\/strong\u003e the Teco TK-150 or any non-WiFi-ready chiller — there's no port for it to connect to.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup\u003c\/h3\u003e\n\u003cp\u003ePlug the module into the WiFi port on the back of a compatible chiller, connect it to your home WiFi network through the Teco app, and it will start reporting temperature and status.\u003c\/p\u003e\n\u003ch3\u003eWarranty and delivery\u003c\/h3\u003e\n\u003cp\u003eCovered by the manufacturer's standard warranty against faulty parts, in addition to your rights under Australian Consumer Law. Ships as a small item at standard parcel rates.\u003c\/p\u003e\n\u003ch3\u003eCommon questions\u003c\/h3\u003e\n\u003ch4\u003eWill this work with my TK-150?\u003c\/h4\u003e\n\u003cp\u003eNo. The TK-150 doesn't have the WiFi port the Nnect module plugs into — this module only fits the TK-500, TK-1000 and TK-2000 R290 range.\u003c\/p\u003e\n\u003ch4\u003eDo I need a separate power supply?\u003c\/h4\u003e\n\u003cp\u003eNo, it draws power from the chiller it's plugged into.\u003c\/p\u003e\n\u003ch4\u003eWhat happens if my tank temperature drifts out of range?\u003c\/h4\u003e\n\u003cp\u003eYou can set alarm thresholds in the app, and it will push a notification to your phone if the reading moves outside them.\u003c\/p\u003e\n\u003ch4\u003eDoes it work on Android?\u003c\/h4\u003e\n\u003cp\u003eYes, on Android 13 and earlier. Android 14 and newer devices aren't yet supported for the initial pairing step — check for an app update if you're on a newer version.\u003c\/p\u003e","brand":"Teco","offers":[{"title":"Default Title","offer_id":55242268213539,"sku":"AA0707","price":399.0,"currency_code":"AUD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0972\/7236\/5347\/files\/teco-nnect-wifi-devic-43106796044579.webp?v=1790231147"},{"product_id":"autoaqua-magnetic-stir-bar","title":"AutoAqua Magnetic Stir Bar","description":"\u003cp\u003e\u003cstrong\u003eThe 3 x 7 mm bar that keeps a dosing container mixed.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe AutoAqua Magnetic Stir Bar (SB-0307) is the spinning element for the AutoAqua Smart Stir. It drops into a dosing container and the Smart Stir's magnetic drive turns it from outside the bottle, keeping supplements that settle out — carbonate powders, amino blends, phytoplankton — evenly suspended. The dose your pump draws from the bottom of the bottle then matches the dose it drew when the bottle was full.\u003c\/p\u003e\n\n\u003ch3\u003eWhat it fits\u003c\/h3\u003e\n\u003cp\u003eAutoAqua lists the SB-0307 as an accessory for the Smart Stir. At 3 mm across and 7 mm long it is sized for the small dosing containers the Smart Stir is built around, not for a mixing drum or a laboratory flask.\u003c\/p\u003e\n\n\u003ch3\u003eKey features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e3 x 7 mm\u003c\/strong\u003e — small enough to pass through a dosing container's neck and to couple with the Smart Stir's drive.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCorrosion-resistant construction\u003c\/strong\u003e — AutoAqua specifies a corrosion-resistant material for permanent immersion, though it does not name the polymer.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDriven through the container wall\u003c\/strong\u003e — nothing passes through the lid, so there is no shaft, no seal and nothing to leak.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNo wearing parts\u003c\/strong\u003e — the bar is the whole mechanism; if it spins freely it is working.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eDimensions\u003c\/th\u003e\n\u003ctd\u003e7 mm long x 3 mm diameter (0.28 in x 0.12 in)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFits\u003c\/th\u003e\n\u003ctd\u003eAutoAqua Smart Stir\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDrive\u003c\/th\u003e\n\u003ctd\u003eMagnetic, through the container wall\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eManufacturer part number\u003c\/th\u003e\n\u003ctd\u003eSB-0307\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\u003c\/table\u003e\n\n\u003ch3\u003eSuitable for, and not suitable for\u003c\/h3\u003e\n\u003cp\u003eSuitable for:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eAutoAqua Smart Stir dosing containers\u003c\/li\u003e\n\u003cli\u003eFreshwater and marine dosing systems\u003c\/li\u003e\n\u003cli\u003eSupplements that settle or separate between doses\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eNot suitable for:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eLarge reservoirs or mixing drums — the bar is sized for small dosing containers\u003c\/li\u003e\n\u003cli\u003eUse on its own — it needs a magnetic stirrer such as the Smart Stir to drive it\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCare and maintenance\u003c\/h3\u003e\n\u003cp\u003eRinse the bar in RO water whenever you refill or change supplement, so residue does not build up and put it out of balance. If dosing accuracy drifts, check the bar is still turning freely rather than sitting stalled against the container wall.\u003c\/p\u003e\n\n\u003ch3\u003eGoes well with\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/autoaqa-smart-stir\"\u003eAutoAqua Smart Stir\u003c\/a\u003e — the drive unit this bar belongs to\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/red-sea-reefdose-4\"\u003eRed Sea ReefDose 4\u003c\/a\u003e — the doser drawing from the container being stirred\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/red-sea-reef-care-calcium-foundation-a-powder\"\u003eRed Sea Reef Care Calcium+ Foundation A (Powder)\u003c\/a\u003e — the kind of made-up supplement that settles between doses\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/controllers-dosing-automation\"\u003eControllers, dosing and automation\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/collections\/autoaqua\"\u003eThe full AutoAqua range\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWarranty and delivery\u003c\/h3\u003e\n\u003cp\u003eShips as a standard parcel. Any manufacturer's warranty offered on this part applies in addition to the consumer guarantees you have under Australian Consumer Law, which cannot be excluded.\u003c\/p\u003e\n\n\u003ch3\u003eCommon questions\u003c\/h3\u003e\n\u003ch4\u003eWhich AutoAqua unit does this stir bar belong to?\u003c\/h4\u003e\n\u003cp\u003eThe AutoAqua Magnetic Stir Bar is listed by AutoAqua as an accessory for the Smart Stir, which provides the magnetic drive that turns it.\u003c\/p\u003e\n\u003ch4\u003eWhy does a dosing container need stirring at all?\u003c\/h4\u003e\n\u003cp\u003eMade-up powders and suspensions settle. Once they do, the doser draws a weaker solution from a container that has been standing than from one just mixed, so the delivered dose changes without anything on the pump changing.\u003c\/p\u003e\n\u003ch4\u003eWhat is the stir bar made of?\u003c\/h4\u003e\n\u003cp\u003eAutoAqua describes it as a durable, corrosion-resistant material suited to long-term aquarium use, but does not publish the specific polymer.\u003c\/p\u003e\n\u003ch4\u003eHow do I clean it?\u003c\/h4\u003e\n\u003cp\u003eRinse it in RO water at each supplement change. Avoid detergents, which are difficult to rinse fully out of a dosing container and end up in the tank.\u003c\/p\u003e","brand":"AutoAqua","offers":[{"title":"Default Title","offer_id":55242280960291,"sku":"AA0344","price":3.0,"currency_code":"AUD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0972\/7236\/5347\/files\/autoaqua-magnetic-stir-bar-43106844705059.webp?v=1790231143"},{"product_id":"autoaqa-smart-stir","title":"AutoAqua Smart Stir","description":"\u003cp\u003e\u003cstrong\u003eReagent mixing that is identical on every test, every time.\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe AutoAqua Smart Stir is a rechargeable magnetic stirrer for aquarium water test kits. A magnetic bar goes into the test vial, the vial sits on the base, and the stirrer mixes the reagent hands-free while you get on with something else. It takes vials up to 27 mm in diameter and switches itself off after five minutes.\u003c\/p\u003e\n\n\u003ch3\u003eWhy hand-swirling is the weak point in a titration\u003c\/h3\u003e\n\u003cp\u003eOn a titration test — alkalinity, calcium, magnesium — the result depends on the colour changing at the right drop. That endpoint is only as repeatable as the mixing.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eHand-swirling varies between tests.\u003c\/strong\u003e Speed, angle and duration change with how much of a hurry you are in, and so does the drop at which the colour turns.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIt varies between people.\u003c\/strong\u003e Two people testing the same water on the same kit can land a drop or two apart, which on an alkalinity kit is a meaningful dKH.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUnmixed reagent reads early.\u003c\/strong\u003e A drop that has not fully dispersed shows local colour before the sample has actually reached the endpoint.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eYour hands are busy.\u003c\/strong\u003e Swirling with one hand while counting drops from a syringe with the other is where miscounts come from.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eConstant, identical agitation removes that variable. It does not make a test kit more accurate than its reagents allow, but it does make consecutive results comparable, which is what actually matters when you are tracking a trend.\u003c\/p\u003e\n\n\u003ch3\u003eWhat this is, and what it is not\u003c\/h3\u003e\n\u003cp\u003eThe Smart Stir is a bench-top laboratory-style stirrer for test vials. It is not a dosing container mixer. It runs on an internal battery for five minutes at a time, is not rated for continuous duty, and is not intended to sit inside or under a dosing reservoir keeping supplements in suspension. If you need a solution kept suspended around the clock in a dosing container, this is the wrong tool.\u003c\/p\u003e\n\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eSKU\u003c\/th\u003e\n\u003ctd\u003eAA0305\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBarcode\u003c\/th\u003e\n\u003ctd\u003e4714041212105\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eFunction\u003c\/th\u003e\n\u003ctd\u003eMagnetic stirrer for mixing water test reagents\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePower\u003c\/th\u003e\n\u003ctd\u003eBuilt-in rechargeable lithium battery, charged by USB 5 V\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCharge time\u003c\/th\u003e\n\u003ctd\u003e120 minutes\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eAuto shut-off\u003c\/th\u003e\n\u003ctd\u003eAfter 5 minutes of operation\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDimensions\u003c\/th\u003e\n\u003ctd\u003e70.5 x 70.5 x 59.5 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eMaximum vial diameter\u003c\/th\u003e\n\u003ctd\u003e27 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eIndicators\u003c\/th\u003e\n\u003ctd\u003eLow battery indicator\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eBase\u003c\/th\u003e\n\u003ctd\u003eNon-slip rubber pads to limit vibration\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWater type\u003c\/th\u003e\n\u003ctd\u003eFreshwater and marine\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eWill my test kit fit?\u003c\/h3\u003e\n\u003cp\u003eThe only fit question is the diameter of the vial. The holder takes vials up to 27 mm across, which covers the standard round test vials supplied with most aquarium titration kits. Measure the outside of your vial at its widest point before ordering if you are close to the limit.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eRound vials\u003c\/strong\u003e sit in the holder as intended.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSquare and rectangular cuvettes\u003c\/strong\u003e will not seat in a 27 mm round holder.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTall narrow vials\u003c\/strong\u003e work, but keep the magnetic bar clear of the syringe tip while you dose.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eVials over 27 mm\u003c\/strong\u003e — including some larger sample cups — are outside the holder size.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWhat's included\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eSmart Stir base\u003c\/li\u003e\n\u003cli\u003eMicro USB charging cable\u003c\/li\u003e\n\u003cli\u003eStirring bar\u003c\/li\u003e\n\u003cli\u003eIron wire, used to lift the magnetic stirring bar back out of a narrow vial\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eNot included\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eA USB power supply. The unit ships with a cable only, and charges from any standard USB 5 V source.\u003c\/li\u003e\n\u003cli\u003eTest kits, reagents or vials.\u003c\/li\u003e\n\u003cli\u003eSpare stirring bars — see \u003ca href=\"\/products\/autoaqua-magnetic-stir-bar\"\u003eAutoAqua Magnetic Stir Bar\u003c\/a\u003e.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eSuitable for, and not suitable for\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eSuitable for\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eTitration kits where a colour endpoint is counted drop by drop — alkalinity, calcium, magnesium\u003c\/li\u003e\n\u003cli\u003eReefers testing several parameters in one session\u003c\/li\u003e\n\u003cli\u003eAnyone whose alkalinity results wander between tests for no obvious reason\u003c\/li\u003e\n\u003cli\u003eHouseholds where more than one person runs the tests\u003c\/li\u003e\n\u003cli\u003eFreshwater and marine test kits alike\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eNot suitable for\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eKeeping dosing supplements suspended in a reservoir — it is a five-minute test-bench tool, not continuous-duty\u003c\/li\u003e\n\u003cli\u003eVials wider than 27 mm, or square cuvettes\u003c\/li\u003e\n\u003cli\u003eMixing anything in the aquarium itself\u003c\/li\u003e\n\u003cli\u003eFast chargers — see the safety note below\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eSafety\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eDo not charge the Smart Stir with a fast charger.\u003c\/strong\u003e AutoAqua states this explicitly; a fast charger may damage the unit. Use a standard USB 5 V source.\u003c\/li\u003e\n\u003cli\u003eKeep the base dry. It is a bench instrument with an internal lithium battery, not aquarium-rated equipment.\u003c\/li\u003e\n\u003cli\u003eKeep the magnetic stirring bar away from probes, magnetic mounts and anything else that will attract it.\u003c\/li\u003e\n\u003cli\u003eRinse the stirring bar between tests. Carry-over reagent on the bar contaminates the next sample.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eCare and maintenance\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eRinse and dry the stirring bar after every test and store it with the base so it does not go missing.\u003c\/li\u003e\n\u003cli\u003eCharge it when the low battery indicator shows rather than leaving it flat between test sessions.\u003c\/li\u003e\n\u003cli\u003eWipe spilled reagent off the base promptly — several aquarium reagents stain.\u003c\/li\u003e\n\u003cli\u003eThe five-minute auto shut-off is a power-saving feature, not a fault. Press the button again if a test needs longer.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eGoes well with\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/autoaqua-magnetic-stir-bar\"\u003eAutoAqua Magnetic Stir Bar\u003c\/a\u003e — the replacement bar for this unit. They are small and easy to lose down a sink, so a spare is worth having.\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/red-sea-kh-alkalinity-pro-testing-kit-75-tests\"\u003eRed Sea KH\/Alkalinity Pro Testing Kit\u003c\/a\u003e — the titration where consistent mixing changes the reading most.\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/red-sea-calcium-pro-testing-kit-75-tests\"\u003eRed Sea Calcium Pro Testing Kit\u003c\/a\u003e — another drop-counted endpoint that benefits from hands-free stirring.\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/seachem-multitest-phosphate-75-tests\"\u003eSeachem MultiTest Phosphate\u003c\/a\u003e — a colorimetric test where even reagent dispersion matters before the colour is read.\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/auto-aqua-digital-inline-tds-titanium-s1\"\u003eAuto Aqua Digital Inline TDS Titanium S1\u003c\/a\u003e — for the RO\/DI side of your testing routine.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWarranty and delivery\u003c\/h3\u003e\n\u003cp\u003eAutoAqua does not publish a warranty term for the Smart Stir. Your rights under the Australian Consumer Law apply to this product and are not limited by any manufacturer's warranty. Ships as a standard parcel. The unit contains a lithium battery, which can restrict air freight on some routes.\u003c\/p\u003e\n\n\u003ch3\u003eCommon questions\u003c\/h3\u003e\n\u003ch4\u003eWhat is the AutoAqua Smart Stir actually for?\u003c\/h4\u003e\n\u003cp\u003eIt is a magnetic stirrer for mixing aquarium water test reagents. The magnetic bar goes into the test vial, the vial sits on the base, and the unit agitates the sample consistently while you count drops or wait out a development time. It is a test-bench tool, not a dosing container mixer.\u003c\/p\u003e\n\u003ch4\u003eCan I use it to keep my dosing supplements mixed in the reservoir?\u003c\/h4\u003e\n\u003cp\u003eNo. The Smart Stir runs on an internal battery and shuts off automatically after five minutes, so it cannot hold a solution in suspension continuously. It is designed for the few minutes a water test takes.\u003c\/p\u003e\n\u003ch4\u003eWhat size test vials does it take?\u003c\/h4\u003e\n\u003cp\u003eVials up to 27 mm in diameter, which is the size of the holder. That covers the round vials supplied with most aquarium titration kits. Square cuvettes and anything wider than 27 mm will not seat in the holder.\u003c\/p\u003e\n\u003ch4\u003eHow is it powered, and how long does it take to charge?\u003c\/h4\u003e\n\u003cp\u003eIt has a built-in rechargeable lithium battery charged over USB at 5 V, and AutoAqua lists a charge time of 120 minutes. A micro USB cable is supplied; a USB power supply is not.\u003c\/p\u003e\n\u003ch4\u003eWhy does it turn itself off after five minutes?\u003c\/h4\u003e\n\u003cp\u003eThat is a deliberate power-saving shut-off, not a fault. Most aquarium tests need far less than five minutes of mixing. If a test needs longer, press the power button again.\u003c\/p\u003e\n\u003ch4\u003eCan I charge it with my phone's fast charger?\u003c\/h4\u003e\n\u003cp\u003eNo. AutoAqua specifically warns against charging the Smart Stir with a fast charger, as it may damage the unit. Use a standard USB 5 V source such as a computer port or a basic USB wall adapter.\u003c\/p\u003e","brand":"AutoAqua","offers":[{"title":"Default Title","offer_id":55242290888995,"sku":"AA0305","price":69.95,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0972\/7236\/5347\/files\/autoaqa-smart-stir-43106844672291.webp?v=1790233226"},{"product_id":"aqua-medic-reefdoser-evo","title":"Aqua Medic Reefdoser EVO","description":"\u003cp\u003e\u003cstrong\u003eSet it, forget it, and stop guessing at supplement doses.\u003c\/strong\u003e The Aqua Medic Reefdoser EVO is an app-controlled dosing pump for reef aquariums, available with 1, 3, 4 or 5 independent channels so you can automate everything from a single kalkwasser top-up to a full calcium, alkalinity, magnesium and trace-element regime. Each channel runs on its own interval schedule, so dosing continues on time whether you're at the tank or not.\u003c\/p\u003e\n\u003ch3\u003eKey features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003e1 to 5 independent channels\u003c\/strong\u003e — choose the EVO 1, 3, 4 or 5 to match the number of supplements you dose, from a single additive up to a full multi-part reef program.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eApp control on EVO 1, 3 and 5\u003c\/strong\u003e — these connect over WiFi and are scheduled and calibrated from Aqua Medic's app, with intervals set from one second to daily.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eLink multiple units\u003c\/strong\u003e — additional EVO 1, 3 or 5 pumps can be added into the same app, so a reef running several supplements isn't limited to one unit's channel count.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEVO 4 with dedicated controller\u003c\/strong\u003e — the EVO 4 ships with its own external controller for interval dosing from seconds to days, for keepers who prefer a standalone unit over app control.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIndependent per-channel programming\u003c\/strong\u003e — each channel is calibrated and scheduled separately, so a fast-growing SPS tank and a slow top-off can run side by side without compromise.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eModel\u003c\/th\u003e\n\u003cth\u003eChannels\u003c\/th\u003e\n\u003cth\u003eControl\u003c\/th\u003e\n\u003cth\u003eDimensions (L × W × H)\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eReefdoser EVO 1\u003c\/td\u003e\n\u003ctd\u003e1\u003c\/td\u003e\n\u003ctd\u003eApp (WiFi)\u003c\/td\u003e\n\u003ctd\u003e97 × 105 × 127 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eReefdoser EVO 3\u003c\/td\u003e\n\u003ctd\u003e3\u003c\/td\u003e\n\u003ctd\u003eApp (WiFi)\u003c\/td\u003e\n\u003ctd\u003e197 × 105 × 127 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eReefdoser EVO 4\u003c\/td\u003e\n\u003ctd\u003e4\u003c\/td\u003e\n\u003ctd\u003eExternal controller (included)\u003c\/td\u003e\n\u003ctd\u003ePump 250 × 130 × 64 mm; controller 140 × 65 × 36 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eReefdoser EVO 5\u003c\/td\u003e\n\u003ctd\u003e5\u003c\/td\u003e\n\u003ctd\u003eApp (WiFi)\u003c\/td\u003e\n\u003ctd\u003e277 × 105 × 127 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eWhich Reefdoser EVO do I need?\u003c\/h3\u003e\n\u003cp\u003eMatch the model to how many supplements you dose, not just how many you dose today — most reefers add a channel eventually.\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eEVO 1\u003c\/strong\u003e — one additive, most often kalkwasser or a single buffer, on tanks that don't yet run a full dosing regime.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEVO 3\u003c\/strong\u003e — the common starting point for a two-part (calcium and alkalinity) or three-part (calcium, alkalinity, magnesium) program.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEVO 4\u003c\/strong\u003e — four channels on a dedicated physical controller rather than the app, for keepers who want dosing control independent of a phone or WiFi network.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eEVO 5\u003c\/strong\u003e — a full three-part program plus trace elements and a top-off channel, or a reef running several supplement lines at once.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWhat's included\u003c\/h3\u003e\n\u003cp\u003eEach Reefdoser EVO ships as a complete dosing unit with its power supply. The EVO 4 additionally includes its external interval controller.\u003c\/p\u003e\n\u003ch3\u003eSuitable for, and not suitable for\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eSuitable for:\u003c\/strong\u003e reef and marine aquariums dosing kalkwasser, two-part or three-part supplements, trace elements, or automated top-off, where precise, unattended timing matters.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eNot suitable for:\u003c\/strong\u003e dosing undiluted, highly concentrated chemicals without first checking compatibility with the pump's wetted parts — check with us if you're unsure about a specific product.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSetup and programming\u003c\/h3\u003e\n\u003cp\u003eOn the EVO 1, 3 and 5, each channel is added to the app, calibrated against a measured test dose, then scheduled on its own interval — anywhere from a single daily dose to dosing spread across the day in smaller, more stable increments. Multiple EVO units can be linked into the same app, so channel count isn't a hard ceiling if your dosing needs grow. The EVO 4 is scheduled instead from its own physical controller, with intervals set from seconds up to several days; Aqua Medic's documentation notes the pump shouldn't be run continuously for more than 15 minutes at a time.\u003c\/p\u003e\n\u003ch3\u003eCare and maintenance\u003c\/h3\u003e\n\u003cp\u003eRinse dosing tubing periodically and re-calibrate each channel if you change tubing, the dosing head, or the concentration of what you're dosing — calibration is done against a measured volume, not assumed from the pump's interval setting.\u003c\/p\u003e\n\u003ch3\u003eWarranty and delivery\u003c\/h3\u003e\n\u003cp\u003eCovered by the manufacturer's warranty in addition to your rights under the Australian Consumer Law. Contact us for the current warranty term on this model. Standard delivery applies — this isn't an oversized or dangerous-goods item.\u003c\/p\u003e\n\u003ch3\u003eCommon questions\u003c\/h3\u003e\n\u003ch4\u003eCan I run the Reefdoser EVO without a WiFi connection?\u003c\/h4\u003e\n\u003cp\u003eThe EVO 1, 3 and 5 are scheduled through Aqua Medic's app and need an initial WiFi connection to set up and calibrate; the EVO 4 is controlled from its own physical controller and doesn't need WiFi at all.\u003c\/p\u003e\n\u003ch4\u003eCan I add more channels later?\u003c\/h4\u003e\n\u003cp\u003eYes — additional EVO 1, 3 or 5 units can be linked into the same app, so you can start with fewer channels and expand as your dosing needs grow.\u003c\/p\u003e\n\u003ch4\u003eDo I need a separate controller for the EVO 4?\u003c\/h4\u003e\n\u003cp\u003eNo — the EVO 4 is sold with its external controller included.\u003c\/p\u003e\n\u003ch4\u003eWhat can I dose with it?\u003c\/h4\u003e\n\u003cp\u003eKalkwasser, two-part and three-part reef supplements, trace elements, and automated top-off water are the common uses; check compatibility with us first for anything unusually concentrated or corrosive.\u003c\/p\u003e","brand":"Aqua Medic","offers":[{"title":"1","offer_id":55285031469347,"sku":"AM104201","price":269.95,"currency_code":"AUD","in_stock":false},{"title":"3","offer_id":55335401980195,"sku":"AM104203","price":363.95,"currency_code":"AUD","in_stock":false},{"title":"4","offer_id":55335402012963,"sku":"AM104144","price":593.95,"currency_code":"AUD","in_stock":false},{"title":"5","offer_id":55335402045731,"sku":"AM104205","price":465.95,"currency_code":"AUD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0972\/7236\/5347\/files\/aqua-medic-reefdoser-evo-43506874843427.webp?v=1790234313"},{"product_id":"aqua-medic-ph-computer-set","title":"Aqua Medic pH Computer Set","description":"\u003cp\u003e\u003cstrong\u003eSet a pH target once, and the computer holds it for you.\u003c\/strong\u003e The Aqua Medic pH Computer Set is a microprocessor-controlled pH meter and controller in one box, built to run a CO2 solenoid on a calcium reactor or dose kalkwasser against a real-time pH reading rather than a timer. It measures and controls across pH 3.0 to 11.0, switches up to 500 W of connected equipment through its own built-in socket, and ships with the BNC pH electrode and calibration fluids you need to get it running the same day it arrives.\u003c\/p\u003e\u003ch3\u003eWhy you need one\u003c\/h3\u003e\u003cp\u003eA calcium reactor dosed on a timer keeps running CO2 whether your tank needs it or not, which lets pH swing further than a reef tolerates well. Wiring the reactor's solenoid through the pH Computer Set instead means CO2 only flows while pH is above your set point, and cuts out the moment it drops back down - the reactor is doing the same job, just responding to the tank instead of the clock.\u003c\/p\u003e\u003ch3\u003eKey features\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eMicroprocessor measurement and control\u003c\/strong\u003e - continuous pH reading, not a periodic timer-based approximation.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e500 W switched socket\u003c\/strong\u003e - plug a CO2 solenoid, doser or other equipment straight into the unit and let it switch power automatically at your set point.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eSelectable control direction\u003c\/strong\u003e - set the unit to switch equipment on above or below your target pH, depending on what you are controlling.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOne-touch electrode calibration\u003c\/strong\u003e - select the calibration key and the unit calibrates itself against the supplied reference fluids.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIncludes what you need to start\u003c\/strong\u003e - plastic-shaft BNC pH electrode and calibration solutions are in the box.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eSpecifications\u003c\/h3\u003e\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSpec\u003c\/th\u003e\n\u003cth\u003eDetail\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eControl range\u003c\/td\u003e\n\u003ctd\u003epH 3.0 - 11.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSwitched output\u003c\/td\u003e\n\u003ctd\u003eUp to 500 W via built-in socket\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eElectrode connection\u003c\/td\u003e\n\u003ctd\u003eBNC\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCalibration\u003c\/td\u003e\n\u003ctd\u003eAutomatic, via calibration key selection\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWeight\u003c\/td\u003e\n\u003ctd\u003eApprox. 1.3 kg\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSKU\u003c\/td\u003e\n\u003ctd\u003eAM20100\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\u003ch3\u003eWhat's included\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003epH Computer Set control unit with built-in 500 W switched socket\u003c\/li\u003e\n\u003cli\u003ePlastic-shaft pH electrode with BNC fitting\u003c\/li\u003e\n\u003cli\u003eCalibration fluids for initial setup\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eNot included\u003c\/h3\u003e\u003cp\u003eThe CO2 solenoid, calcium reactor, kalkwasser doser or other equipment you are controlling - the computer switches power to your existing gear, it does not replace it. An electrode holder or mounting bracket is not confirmed as included; check with us if that matters for your setup.\u003c\/p\u003e\u003ch3\u003eWhich Aqua Medic pH controller do I need?\u003c\/h3\u003e\u003cp\u003eAqua Medic also sells a standalone pH Monitor, which reads and can switch a smaller 5 A load but is built primarily as a monitoring and alarm unit. The pH Computer Set is the step up: a 500 W switched output aimed squarely at running a calcium reactor's CO2 solenoid or a similar higher-draw device directly from the pH reading.\u003c\/p\u003e\u003ch3\u003eSuitable for, and not suitable for\u003c\/h3\u003e\u003cp\u003e\u003cstrong\u003eSuitable for:\u003c\/strong\u003e pH-triggered control of a calcium reactor's CO2 solenoid, kalkwasser dosing pumps, or other equipment drawing up to 500 W, on freshwater or marine systems.\u003c\/p\u003e\u003cp\u003e\u003cstrong\u003eNot suitable for:\u003c\/strong\u003e switching equipment that draws more than 500 W through its built-in socket, or as a replacement for a dedicated dosing pump's own safety cut-offs.\u003c\/p\u003e\u003ch3\u003eSafety\u003c\/h3\u003e\u003cp\u003eThis is a mains-powered controller switching a live socket output - have it installed away from splash zones and on a circuit protected by a residual current device (RCD), as with any aquarium electrical equipment. The manufacturer's specification lists the unit as 220 V rated; we have not been able to confirm from Aqua Medic's Australian documentation whether Australian stock ships multi-region rated or needs a step-down transformer for our 230-240 V supply. If that matters for your installation, contact us before ordering and we will confirm with our supplier.\u003c\/p\u003e\u003ch3\u003eCare and maintenance\u003c\/h3\u003e\u003cp\u003eRecalibrate the electrode roughly every four weeks using fresh Aqua Medic pH 7 and pH 9 calibration fluid, and replace the electrode itself when it stops holding a stable calibration - Aqua Medic backs the glass membrane on its pH and mV electrodes for six months as a wear item rather than under the full unit warranty.\u003c\/p\u003e\u003ch3\u003eGoes well with\u003c\/h3\u003e\u003cul\u003e\n\u003cli\u003eAqua Medic pH 7 Test Fluid 60ml - for routine two-point calibration.\u003c\/li\u003e\n\u003cli\u003eAqua Medic pH 9 Test Fluid 60ml - pairs with the pH 7 fluid for a full calibration.\u003c\/li\u003e\n\u003cli\u003eAqua Medic Refillable Plastic pH Probe 120mm - a spare or replacement electrode for when the original wears out.\u003c\/li\u003e\n\u003c\/ul\u003e\u003ch3\u003eWarranty and delivery\u003c\/h3\u003e\u003cp\u003eSold with the benefit of Australian Consumer Law's consumer guarantees regardless of any separate manufacturer terms. The electrode is a wear item with a shorter service life than the control unit itself - see Care and maintenance above.\u003c\/p\u003e\u003ch3\u003eCommon questions\u003c\/h3\u003e\u003ch4\u003eCan the pH Computer Set run my calcium reactor's CO2 solenoid directly?\u003c\/h4\u003e\u003cp\u003eYes - the unit switches up to 500 W through its built-in socket, which comfortably covers a standard CO2 solenoid valve, and it will cut power once your tank reaches the pH you have set.\u003c\/p\u003e\u003ch4\u003eDo I need a separate pH monitor as well?\u003c\/h4\u003e\u003cp\u003eNo - the pH Computer Set both measures and displays pH, so it replaces a standalone monitor for the electrode it is connected to.\u003c\/p\u003e\u003ch4\u003eHow is this different from the Aqua Medic pH Monitor?\u003c\/h4\u003e\u003cp\u003eThe pH Monitor is built primarily around reading and alarming, with a smaller 5 A relay; the pH Computer Set is built around control, with a 500 W switched socket sized for equipment like a calcium reactor's CO2 solenoid.\u003c\/p\u003e\u003ch4\u003eWhat happens if the electrode fails?\u003c\/h4\u003e\u003cp\u003eThe control unit keeps working - you replace the electrode on its own using a compatible BNC pH probe, such as Aqua Medic's refillable plastic probe, rather than replacing the whole computer.\u003c\/p\u003e","brand":"Aqua Medic","offers":[{"title":"Default Title","offer_id":55285031600419,"sku":"AM20100","price":1118.95,"currency_code":"AUD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0972\/7236\/5347\/files\/aqua-medic-ph-computer-set-43506875433251.webp?v=1790234314"},{"product_id":"aqua-medic-t-controller-twin-2-0","title":"Aqua Medic T Controller Twin 2.0","description":"\u003cp\u003e\u003cstrong\u003eOne controller, two outlets, and a 0.1°C switching accuracy that keeps a heater and a chiller from fighting each other.\u003c\/strong\u003e The Aqua Medic T Controller Twin 2.0 is a dual-channel temperature controller that switches a heating device and a cooling device from a single seawater-resistant probe, holding your system within a set range day and night without you adjusting a dial. It suits any freshwater or marine tank where temperature swings — Brisbane summers on the cooling side, winter nights on the heating side — are the actual problem, not the device brand.\u003c\/p\u003e\n\u003ch3\u003eKey features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eTwo independent switched outlets\u003c\/strong\u003e — one heating (up to 1,200 W), one cooling (up to 460 W) — run from the one unit and the one probe.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e0.1°C resolution and switching accuracy\u003c\/strong\u003e — set point adjustable across 16–40°C in 0.1°C steps, so the controller isn't rounding your target.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBuilt-in switch delay\u003c\/strong\u003e — a minimum 30-second gap between heating and cooling outlets stops the two devices cycling against each other.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eBattery-backed memory\u003c\/strong\u003e — your set point survives a power cut; the controller doesn't reset to default when the power comes back.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eIP65 housing\u003c\/strong\u003e — rated against splash and dust in a wet aquarium cabinet.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eAudible alarm\u003c\/strong\u003e — a single adjustable threshold sounds if the tank drifts outside your set range.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSpec\u003c\/th\u003e\n\u003cth\u003eValue\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eVoltage\u003c\/td\u003e\n\u003ctd\u003e220–240 V, 50 Hz\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHeating outlet, max load\u003c\/td\u003e\n\u003ctd\u003e1,200 W\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eCooling outlet, max load\u003c\/td\u003e\n\u003ctd\u003e460 W\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTemperature range\u003c\/td\u003e\n\u003ctd\u003e16–40°C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eResolution \/ switching accuracy\u003c\/td\u003e\n\u003ctd\u003e0.1°C\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eProbe\u003c\/td\u003e\n\u003ctd\u003e1 x replaceable, seawater-resistant, max immersion depth 30 cm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eProbe cable length\u003c\/td\u003e\n\u003ctd\u003eApprox. 1.8–2 m (Aqua Medic's own documentation gives slightly different figures across sources)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHousing rating\u003c\/td\u003e\n\u003ctd\u003eIP65\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMinimum switch delay\u003c\/td\u003e\n\u003ctd\u003e30 seconds between heating and cooling outlets\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eWarranty\u003c\/td\u003e\n\u003ctd\u003e24 months, manufacturer\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eWill it fit my setup?\u003c\/h3\u003e\n\u003cp\u003eThe T Controller Twin 2.0 doesn't heat or cool anything itself — it's the brain that switches devices you already own, or are buying separately. Check your heater's wattage against the 1,200 W heating outlet limit and your chiller or fan against the 460 W cooling outlet limit before plugging in; anything under those figures is fine on a single channel.\u003c\/p\u003e\n\u003ch3\u003eWhat's included\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eT Controller Twin 2.0 unit\u003c\/li\u003e\n\u003cli\u003e1 x seawater-resistant temperature probe with suction-cup mount\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eNot included\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003eHeating device (heater, in-line heater)\u003c\/li\u003e\n\u003cli\u003eCooling device (chiller, cooling fan)\u003c\/li\u003e\n\u003cli\u003eWall-mounting bracket for the controller body — the Aqua Medic Universal Holder fits this unit if you want it off the cabinet floor\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSafety\u003c\/h3\u003e\n\u003cp\u003eThis is a mains-powered switching device controlling other mains-powered equipment — run it on a circuit protected by an RCD rated 30 mA or lower. The built-in switch delay is a safety feature, not a fault: don't be concerned if heating and cooling don't swap over instantly.\u003c\/p\u003e\n\u003ch3\u003eCare and maintenance\u003c\/h3\u003e\n\u003cp\u003eThe temperature probe is replaceable independently of the controller body if it fails or drifts — check it against a separate thermometer occasionally, as with any electronic probe.\u003c\/p\u003e\n\u003ch3\u003eGoes well with\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eAqua Medic Universal Holder\u003c\/strong\u003e — wall-mounts the controller body off the cabinet floor.\u003c\/li\u003e\n\u003cli\u003eA compatible in-tank heater sized under 1,200 W for the heating outlet.\u003c\/li\u003e\n\u003cli\u003eA cooling fan or chiller sized under 460 W for the cooling outlet.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eWarranty and delivery\u003c\/h3\u003e\n\u003cp\u003eCovered by Aqua Medic's 24-month manufacturer warranty against manufacturing defects, in addition to your rights under Australian Consumer Law. Standard freight — this is a small, light item with no special handling requirements.\u003c\/p\u003e\n\u003ch3\u003eCommon questions\u003c\/h3\u003e\n\u003ch4\u003eCan it run a heater and a chiller at the same time?\u003c\/h4\u003e\n\u003cp\u003eYes — that's the point of the twin outlet design. One channel switches heating, the other switches cooling, from the same temperature reading, with a built-in delay so the two never activate against each other.\u003c\/p\u003e\n\u003ch4\u003eDoes it come with a heater or chiller?\u003c\/h4\u003e\n\u003cp\u003eNo. The T Controller Twin 2.0 is the switching unit only — you connect your own heating and cooling equipment to its two outlets.\u003c\/p\u003e\n\u003ch4\u003eWhat's the maximum wattage it can switch?\u003c\/h4\u003e\n\u003cp\u003e1,200 W on the heating outlet and 460 W on the cooling outlet. Add up the wattage of whatever you're plugging into each outlet and stay under those figures.\u003c\/p\u003e\n\u003ch4\u003eIs it suitable for marine tanks?\u003c\/h4\u003e\n\u003cp\u003eYes — the probe is seawater-resistant and the controller itself is a general-purpose temperature switch suitable for freshwater or marine systems.\u003c\/p\u003e\n\u003ch4\u003eWhat happens to my settings if the power goes out?\u003c\/h4\u003e\n\u003cp\u003eThe set point is retained through a power interruption via the controller's battery-backed memory, so it resumes at the same setting once power returns.\u003c\/p\u003e","brand":"Aqua Medic","offers":[{"title":"Default Title","offer_id":55285031731491,"sku":"AM20525","price":205.95,"currency_code":"AUD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0972\/7236\/5347\/files\/aqua-medic-t-controller-twin-10278091817251-1-dq.webp?v=1790372665"},{"product_id":"reeflink","title":"ReefLink","description":"\u003cp\u003e\u003cstrong\u003eEvery EcoTech device already talks to the others — ReefLink is what lets them talk to your phone.\u003c\/strong\u003e The EcoTech Marine ReefLink is a WiFi bridge that connects Radion lighting, VorTech wavemakers and Vectra return pumps to EcoSmart Live, EcoTech's free cloud control platform. It sits on your network like a router, links to your EcoTech gear over its own built-in radio, and puts scheduling, dosing integration and live monitoring in a browser or app instead of a row of dials on the tank.\u003c\/p\u003e\n\n\u003ch3\u003eKey features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eOne hub, whole-system control\u003c\/strong\u003e — Radion, VorTech and Vectra devices connect to ReefLink over EcoTech's own RF protocol, no separate dongles per device.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eCloud-based, not locked to one phone\u003c\/strong\u003e — control and schedule from any computer, tablet or phone signed in to EcoSmart Live.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWired or wireless uplink\u003c\/strong\u003e — connects to your network over 802.11n WiFi or a direct 10\/100 Mb Ethernet cable, useful where WiFi reception near the tank is weak.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eConnection status at a glance\u003c\/strong\u003e — an LED status ring on the unit shows whether it's linked to your equipment and to the internet.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eMulti-tank capable\u003c\/strong\u003e — one ReefLink can manage more than one tank's worth of EcoTech equipment from the same account.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003eFunction\u003c\/th\u003e\n\u003ctd\u003eWiFi\/Ethernet bridge for EcoSmart Live cloud control\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eCompatible devices\u003c\/th\u003e\n\u003ctd\u003eRadion LED lighting, VorTech wavemakers, Vectra return pumps and other EcoSmart-enabled EcoTech Marine equipment\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWiFi\u003c\/th\u003e\n\u003ctd\u003e802.11n\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eWired option\u003c\/th\u003e\n\u003ctd\u003e10\/100 Mb Ethernet, direct connect\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDevice link\u003c\/th\u003e\n\u003ctd\u003eBuilt-in RF communication with EcoTech equipment — no separate dongles\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePower input\u003c\/th\u003e\n\u003ctd\u003e110–240 V, 50\/60 Hz\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eStatus indicator\u003c\/th\u003e\n\u003ctd\u003eLED connection ring\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eSuitable for, and not suitable for\u003c\/h3\u003e\n\u003cp\u003eSuitable for reef and marine setups running two or more EcoSmart-enabled EcoTech devices — Radion lights, VorTech wavemakers, Vectra pumps — where remote scheduling, dosing integration or off-site monitoring is worth having. Not needed for a single VorTech or Radion run entirely from its own onboard controls with no remote access required; those devices work standalone without ReefLink.\u003c\/p\u003e\n\n\u003ch3\u003eSetup, use, dosing or feeding\u003c\/h3\u003e\n\u003cp\u003eReefLink connects to your home network over WiFi or Ethernet, then links to your EcoTech devices over their built-in RF radio — no additional dongles or adapters. Once connected, scheduling, ramping and dosing integration are managed through the EcoSmart Live web platform from a computer, tablet or phone rather than the buttons on each individual device. An EcoSmart Live account is required to use the cloud features.\u003c\/p\u003e\n\n\u003ch3\u003eCompatibility, spares and supersession\u003c\/h3\u003e\n\u003cp\u003eWorks with current-generation Radion, VorTech and Vectra hardware, and with EcoTech's dosing accessories where fitted. Older EcoTech devices without EcoSmart Live support won't connect to ReefLink — check your device's own listing for EcoSmart compatibility if you're running older-generation gear.\u003c\/p\u003e\n\n\u003ch3\u003eWarranty and delivery\u003c\/h3\u003e\n\u003cp\u003eCovered by EcoTech Marine's standard manufacturer warranty, in addition to your rights under Australian Consumer Law. Standard delivery Australia-wide.\u003c\/p\u003e\n\n\u003ch3\u003eCommon questions\u003c\/h3\u003e\n\u003ch4\u003eDo I need a ReefLink to use my Radion or VorTech?\u003c\/h4\u003e\n\u003cp\u003eNo — both run fine from their own onboard controls. ReefLink adds remote scheduling, monitoring and dosing integration through EcoSmart Live; it isn't required for basic operation.\u003c\/p\u003e\n\u003ch4\u003eCan one ReefLink control more than one tank?\u003c\/h4\u003e\n\u003cp\u003eYes, provided the equipment on each tank is EcoSmart-enabled and linked to the same EcoSmart Live account.\u003c\/p\u003e\n\u003ch4\u003eDoes it need to be plugged into my router, or can it run on WiFi?\u003c\/h4\u003e\n\u003cp\u003eEither — ReefLink connects over 802.11n WiFi or a direct 10\/100 Mb Ethernet cable if you'd rather not rely on wireless reception near the tank.\u003c\/p\u003e\n\u003ch4\u003eDo I need to keep it connected to the internet at all times?\u003c\/h4\u003e\n\u003cp\u003eNo — your Radion, VorTech and Vectra devices run on their own onboard controls independent of ReefLink; it adds cloud access and scheduling on top, not core operation.\u003c\/p\u003e\n\n\u003ch3\u003eGoes well with\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/products\/radion-led-premium-hanging-kit-gen5\"\u003eRadion LED Premium Hanging Kit gen5\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/products\/vortech-mp40qd\"\u003eEcoTech Marine VorTech MP40QD Wavemaker\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/products\/vectra-s2-centrifugal-pump\"\u003eVectra S2 Centrifugal Pump\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"EcoTech Marine","offers":[{"title":"Default Title","offer_id":55293349527843,"sku":"MPBR10","price":272.9,"currency_code":"AUD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0972\/7236\/5347\/files\/reeflink-46120746484003.webp?v=1790240279"},{"product_id":"versa-dosing-pump-single","title":"Versa Dosing Pump - Single","description":"\u003cp\u003e\u003cstrong\u003eAdd one more precisely dosed reagent without buying a second base station.\u003c\/strong\u003e The EcoTech Marine Versa Dosing Pump (VX-1) is a single-channel peristaltic doser with its own power supply, so it runs standalone on a reef system that only needs one automated reagent — or as an extra channel alongside an existing Versa Base Station setup.\u003c\/p\u003e\n\u003ch3\u003eKey features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eRuns standalone\u003c\/strong\u003e — includes its own power supply, so a Base Station isn't required for a single reagent.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDosing accuracy to within 2%\u003c\/strong\u003e — precise enough for daily alkalinity or calcium dosing without constant recalibration.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e6 µL minimum, up to 300 mL maximum per dose\u003c\/strong\u003e — covers trace-element dosing through to larger volume tasks on the same pump.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUp to 30 discrete dosing events a day\u003c\/strong\u003e — split a daily dose into smaller, more frequent doses to reduce pH swings.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree dosing modes\u003c\/strong\u003e — Auto (scheduled), Continuous (constant run) and Manual (set volume or duration on demand).\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSpecification\u003c\/th\u003e\n\u003cth\u003eValue\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eDosing accuracy\u003c\/td\u003e\n\u003ctd\u003e2% or better\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMinimum dose\u003c\/td\u003e\n\u003ctd\u003e6 µL per dose\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eContinuous flow\u003c\/td\u003e\n\u003ctd\u003eUp to 200 mL per minute\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMaximum volumetric capacity\u003c\/td\u003e\n\u003ctd\u003eUp to 300 mL per dose\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDosing events\u003c\/td\u003e\n\u003ctd\u003eUp to 30 per day\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower consumption\u003c\/td\u003e\n\u003ctd\u003e12 W\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInput voltage\u003c\/td\u003e\n\u003ctd\u003e100–240 V AC, 50\/60 Hz\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePeak inrush current\u003c\/td\u003e\n\u003ctd\u003e1.3 A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDimensions\u003c\/td\u003e\n\u003ctd\u003e80 x 59.4 x 106.9 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTubing\u003c\/td\u003e\n\u003ctd\u003e1\/4 in OD, push-to-connect or barbed fittings\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eControl\u003c\/td\u003e\n\u003ctd\u003eMobius app (iOS\/Android)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSKU\u003c\/td\u003e\n\u003ctd\u003eMPVX-1\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eWhat's included\u003c\/h3\u003e\n\u003cp\u003eOne Versa dosing pump with its own power supply, plus a female PTC connector and a barbed adapter for tubing.\u003c\/p\u003e\n\u003ch4\u003eNot included\u003c\/h4\u003e\n\u003cp\u003eA dosing container for your reagent, and dosing line tubing beyond the fittings supplied — extra lengths are sold separately by colour.\u003c\/p\u003e\n\u003ch3\u003eWhich Versa do I need?\u003c\/h3\u003e\n\u003cp\u003eThis single pump suits one reagent. Dosing two or more reagents on independent schedules works out cheaper as the \u003ca href=\"\/products\/versa-dosing-pump-4-pumps-base-station\"\u003e4-pump kit with Base Station\u003c\/a\u003e, which also removes the need for a separate power brick per pump.\u003c\/p\u003e\n\u003ch3\u003eSuitable for, and not suitable for\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eSuitable for:\u003c\/strong\u003e a single automated reagent — commonly alkalinity or calcium on a reef tank, or a single additive on a planted freshwater system. \u003cstrong\u003eNot suitable for:\u003c\/strong\u003e multi-reagent dosing without buying multiple single units and power supplies — the 4-pump kit is the better value path there.\u003c\/p\u003e\n\u003ch3\u003eRunning costs\u003c\/h3\u003e\n\u003cp\u003eAt its rated 12 W draw, run continuously this pump uses roughly 105 kWh a year — about $32 annually at a 30c\/kWh tariff. Dosing pumps run in short bursts rather than continuously, so actual draw is typically well under this ceiling figure.\u003c\/p\u003e\n\u003ch3\u003eCare and maintenance\u003c\/h3\u003e\n\u003cp\u003eThe dosing tubing compressed by the pump's rotor is the wear item, not the pump body — plan to replace the dosing line periodically rather than expecting the original tubing to last indefinitely.\u003c\/p\u003e\n\u003ch3\u003eWarranty and delivery\u003c\/h3\u003e\n\u003cp\u003eCovered by EcoTech Marine's manufacturer warranty, in addition to your rights under Australian Consumer Law. Ships as a standard parcel.\u003c\/p\u003e\n\u003ch3\u003eGoes well with\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/versa-dosing-pump-4-pumps-base-station\"\u003eVersa Dosing Pump – 4 Pumps \u0026amp; Base Station\u003c\/a\u003e — for dosing more than one reagent from a single power supply.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCommon questions\u003c\/h3\u003e\n\u003ch4\u003eDo I need a Base Station to use this pump?\u003c\/h4\u003e\n\u003cp\u003eNo. This single unit includes its own power supply and runs standalone.\u003c\/p\u003e\n\u003ch4\u003eCan I add this to an existing Base Station later?\u003c\/h4\u003e\n\u003cp\u003eThe Base Station docks up to four pumps and shares one power supply between them; this standalone unit has its own supply, so check compatibility before combining the two rather than assuming they interchange.\u003c\/p\u003e\n\u003ch4\u003eHow precise is the dosing?\u003c\/h4\u003e\n\u003cp\u003eEcoTech states 2% accuracy or better, with doses as small as 6 µL a minute — precise enough for daily reef dosing.\u003c\/p\u003e\n\u003ch4\u003eWhat tubing does it use?\u003c\/h4\u003e\n\u003cp\u003e1\/4 in OD tubing with push-to-connect or barbed fittings — the same tubing used across the Versa range.\u003c\/p\u003e","brand":"EcoTech Marine","offers":[{"title":"Default Title","offer_id":55293350543651,"sku":"MPVX-1","price":349.9,"currency_code":"AUD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0972\/7236\/5347\/files\/versa-dosing-pump-single-43203670016291.webp?v=1790235416"},{"product_id":"versa-base-station","title":"Versa Base Station","description":"\u003cp\u003e\u003cstrong\u003eFour dosing pumps, one power cord.\u003c\/strong\u003e The EcoTech Marine Versa Base Station is the docking rail for the Versa peristaltic dosing pump system: it lets you clip up to four individual Versa VX-1 pump heads onto a single rail and run them from one consolidated power supply, instead of four separate wall adaptors cluttering the cabinet behind your tank.\u003c\/p\u003e\n\n\u003ch3\u003eKey features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eDocks up to four Versa pumps\u003c\/strong\u003e – slide each VX-1 pump head onto the rail; no separate stand or bracket needed per pump.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOne power supply for the whole rail\u003c\/strong\u003e – replaces up to four individual Versa power supplies with a single universal adaptor.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTactile indexing buttons\u003c\/strong\u003e – locate and select an individual pump on the rail by feel, without needing to see the unit from behind the cabinet door.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eWorks with the Mobius app\u003c\/strong\u003e – each docked pump is still programmed individually, in Auto, Continuous or Manual mode.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eTidier cabinet wiring\u003c\/strong\u003e – one cord and one power point instead of up to four.\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth\u003ePump capacity\u003c\/th\u003e\n\u003ctd\u003eDocks up to 4 x Versa VX-1 pump heads\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eDimensions\u003c\/th\u003e\n\u003ctd\u003e325 mm L x 22 mm W x 89.4 mm H\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eInput voltage\u003c\/th\u003e\n\u003ctd\u003e110–240 VAC, 50\/60 Hz (universal)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePower consumption\u003c\/th\u003e\n\u003ctd\u003eUp to 60 W with 4 pumps docked and running\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003ePeak inrush current\u003c\/th\u003e\n\u003ctd\u003e2.0 A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth\u003eControl\u003c\/th\u003e\n\u003ctd\u003eTactile indexing buttons per pump position; full programming via the Mobius app\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\n\u003ch3\u003eWhich one do I need? Base Station vs standalone Versa\u003c\/h3\u003e\n\u003cp\u003eA single Versa VX-1 pump ships with its own power supply and its own mounting bracket, so you don't need a Base Station to run one or two pumps. The Base Station earns its keep once you're running three or four dosers – calcium, alkalinity, magnesium and a trace element, say – and don't want four separate power bricks fighting for space in the stand.\u003c\/p\u003e\n\n\u003ch3\u003eSuitable for, and not suitable for\u003c\/h3\u003e\n\u003cp\u003eSuitable for consolidating up to four Versa VX-1 dosing pump heads onto one rail and one power supply. Not a dosing pump itself – you still need to buy the Versa pump heads separately, and it doesn't work with any other brand's peristaltic pump.\u003c\/p\u003e\n\n\u003ch3\u003eWhat's included\u003c\/h3\u003e\n\u003cp\u003eBase station rail and a power supply. Versa pump heads, tubing and dosing containers are sold separately.\u003c\/p\u003e\n\n\u003ch3\u003eCare and maintenance\u003c\/h3\u003e\n\u003cp\u003eThe base station itself has no consumable parts. Maintenance – tube replacement and lubrication – is done at the individual pump head, on the schedule EcoTech publishes for the Versa system: lubricate every 3,000 gallons treated or 6 months, and replace the tube assembly every 6,000 gallons or 12 months, whichever comes first for each pump.\u003c\/p\u003e\n\n\u003ch3\u003eSafety\u003c\/h3\u003e\n\u003cp\u003eMains-powered accessory rated for 110–240 VAC, 50\/60 Hz – suitable for the Australian 240 V supply without a separate transformer. Keep the power supply and cabling clear of any water spill or splash zone in the cabinet.\u003c\/p\u003e\n\n\u003ch3\u003eGoes well with\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"\/products\/versa-replacement-tube-assy-w-retainer\"\u003eVersa Replacement Tube Assy w Retainer\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/versa-single-24v-1a\"\u003eVersa Single 24V 1A\u003c\/a\u003e power supply – a spare for a standalone pump\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"\/products\/versa-single-mounting-bracket\"\u003eVersa Single Mounting Bracket\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\n\u003ch3\u003eWarranty and delivery\u003c\/h3\u003e\n\u003cp\u003eCovered by EcoTech Marine's standard warranty terms, in addition to your rights under Australian Consumer Law. Standard delivery Australia-wide.\u003c\/p\u003e\n\n\u003ch3\u003eCommon questions\u003c\/h3\u003e\n\u003ch4\u003eDo I need a Base Station to run a Versa pump?\u003c\/h4\u003e\n\u003cp\u003eNo. A single Versa VX-1 pump comes with its own power supply and mounting bracket and runs perfectly well on its own. The Base Station is for consolidating multiple pumps.\u003c\/p\u003e\n\u003ch4\u003eCan I add pumps to the Base Station later?\u003c\/h4\u003e\n\u003cp\u003eYes – dock up to four in total, and add them as your dosing needs grow, up to that limit.\u003c\/p\u003e\n\u003ch4\u003eDoes each pump still need its own program?\u003c\/h4\u003e\n\u003cp\u003eYes. The Base Station shares power and physical mounting, but each pump head is still scheduled individually through the Mobius app.\u003c\/p\u003e\n\u003ch4\u003eWill it work on Australian 240 V power?\u003c\/h4\u003e\n\u003cp\u003eYes – the power supply accepts 110–240 VAC, 50\/60 Hz, so it runs on Australian mains without a converter.\u003c\/p\u003e","brand":"EcoTech Marine","offers":[{"title":"Default Title","offer_id":55293350838563,"sku":"MPVXB-1","price":295.9,"currency_code":"AUD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0972\/7236\/5347\/files\/versa-base-station-43876725162275.webp?v=1790240280"},{"product_id":"versa-dosing-pump-4-pumps-base-station","title":"Versa Dosing Pump - 4 Pumps \u0026 Base Station","description":"\u003cp\u003e\u003cstrong\u003eAutomate four reagents from one rail, without four separate power bricks.\u003c\/strong\u003e The EcoTech Marine Versa Dosing Pump kit bundles four peristaltic dosing pumps with a Base Station, so calcium, alkalinity, magnesium and a fourth additive can all run on independent schedules from a single 60 W power supply and the Mobius app.\u003c\/p\u003e\n\u003ch3\u003eKey features\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cstrong\u003eFour independent dosing pumps\u003c\/strong\u003e — each runs its own schedule, so different reagents can dose at different times and rates from the one unit.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eDosing accuracy to within 2%\u003c\/strong\u003e — precise enough for daily alkalinity and calcium dosing on a reef system without constant recalibration.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003e6 µL minimum, up to 300 mL maximum per dose\u003c\/strong\u003e — covers everything from trace-element dosing to bulk water changes on the same hardware.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eUp to 30 discrete dosing events per pump, per day\u003c\/strong\u003e — reagents can be split into small, frequent doses rather than one large daily slug.\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eThree dosing modes\u003c\/strong\u003e — Auto (scheduled), Continuous (constant run) and Manual (set volume or duration on demand).\u003c\/li\u003e\n\u003cli\u003e\n\u003cstrong\u003eOne power supply for all four pumps\u003c\/strong\u003e — the Base Station consolidates power and cabling that would otherwise need four separate plug packs.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eSpecifications\u003c\/h3\u003e\n\u003ctable\u003e\n\u003cthead\u003e\u003ctr\u003e\n\u003cth\u003eSpecification\u003c\/th\u003e\n\u003cth\u003eValue\u003c\/th\u003e\n\u003c\/tr\u003e\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003ePumps included\u003c\/td\u003e\n\u003ctd\u003e4\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDosing accuracy\u003c\/td\u003e\n\u003ctd\u003e2% or better\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMinimum dose\u003c\/td\u003e\n\u003ctd\u003e6 µL per dose\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eContinuous flow\u003c\/td\u003e\n\u003ctd\u003eUp to 200 mL per minute\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMaximum volumetric capacity\u003c\/td\u003e\n\u003ctd\u003eUp to 300 mL per dose\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDosing events\u003c\/td\u003e\n\u003ctd\u003eUp to 30 per pump per day\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePower consumption\u003c\/td\u003e\n\u003ctd\u003e60 W (kit, via Base Station)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInput voltage\u003c\/td\u003e\n\u003ctd\u003e110–240 V AC, 50\/60 Hz\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003ePeak inrush current\u003c\/td\u003e\n\u003ctd\u003e2.0 A\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eKit dimensions\u003c\/td\u003e\n\u003ctd\u003e325.1 x 81.5 x 107 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eTubing\u003c\/td\u003e\n\u003ctd\u003e1\/4 in OD, push-to-connect or barbed fittings\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eControl\u003c\/td\u003e\n\u003ctd\u003eMobius app (iOS\/Android)\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eSKU\u003c\/td\u003e\n\u003ctd\u003eMPVXF-1\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003eWhat's included\u003c\/h3\u003e\n\u003cp\u003eFour Versa dosing pumps, one Base Station, and the Base Station's power supply. EcoTech's own listing is explicit that this kit does not include individual power supplies for each pump — the Base Station runs all four from its single 60 W supply.\u003c\/p\u003e\n\u003ch4\u003eNot included\u003c\/h4\u003e\n\u003cp\u003eDosing containers or reservoirs for your reagents, and the dosing line tubing to run between the pumps and your tank or containers — tubing is sold separately by the length and colour.\u003c\/p\u003e\n\u003ch3\u003eSetup and use\u003c\/h3\u003e\n\u003cp\u003eEach of the four pump heads docks onto the Base Station rail and draws power from it, so there's one mains lead for the whole kit rather than four. Reagents are scheduled independently through the Mobius app in Auto, Continuous or Manual mode, and each pump can run up to 30 separate dosing events a day — useful for splitting a large daily alkalinity dose into several smaller ones to reduce pH swings.\u003c\/p\u003e\n\u003ch3\u003eSuitable for, and not suitable for\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003eSuitable for:\u003c\/strong\u003e reef systems dosing two to four reagents (calcium, alkalinity, magnesium, trace elements) on independent schedules, and anyone wanting to consolidate multiple single dosing pumps onto one power supply. \u003cstrong\u003eNot suitable for:\u003c\/strong\u003e single-reagent setups — a single \u003ca href=\"\/products\/versa-dosing-pump-single\"\u003eVersa Dosing Pump\u003c\/a\u003e is cheaper and doesn't need the Base Station.\u003c\/p\u003e\n\u003ch3\u003eRunning costs\u003c\/h3\u003e\n\u003cp\u003eAt its rated 60 W draw, run continuously the kit uses roughly 526 kWh a year — about $158 annually at a 30c\/kWh tariff. In practice, dosing pumps run in short bursts rather than continuously, so actual draw and cost will typically be well below this ceiling figure.\u003c\/p\u003e\n\u003ch3\u003eCare and maintenance\u003c\/h3\u003e\n\u003cp\u003ePeristaltic dosing pumps wear at the tubing that's compressed by the rotor, not the pump body. Budget to replace dosing lines periodically rather than expecting the original tubing to last indefinitely, particularly on the reagent lines dosing daily.\u003c\/p\u003e\n\u003ch3\u003eWarranty and delivery\u003c\/h3\u003e\n\u003cp\u003eCovered by EcoTech Marine's manufacturer warranty, in addition to your rights under Australian Consumer Law. Ships as a standard parcel.\u003c\/p\u003e\n\u003ch3\u003eGoes well with\u003c\/h3\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003ca href=\"\/products\/versa-dosing-pump-single\"\u003eVersa Dosing Pump – Single\u003c\/a\u003e — for adding a fifth reagent line beyond the four this kit covers (needs its own Base Station or independent power).\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch3\u003eCommon questions\u003c\/h3\u003e\n\u003ch4\u003eCan I add a fifth pump to this kit?\u003c\/h4\u003e\n\u003cp\u003eNot to the same Base Station — it docks a maximum of four pumps. A fifth reagent would need a second Base Station or a standalone Versa Dosing Pump running on its own power supply.\u003c\/p\u003e\n\u003ch4\u003eDo I need four separate reservoirs?\u003c\/h4\u003e\n\u003cp\u003eYes, one dosing container per reagent. The kit doses whatever you connect each pump to; it doesn't include containers.\u003c\/p\u003e\n\u003ch4\u003eHow precise is the dosing, really?\u003c\/h4\u003e\n\u003cp\u003eEcoTech states 2% accuracy or better, with doses as small as 6 µL a minute available — precise enough for daily reef dosing without needing to compensate for pump drift.\u003c\/p\u003e\n\u003ch4\u003eWhat happens if the Base Station loses power?\u003c\/h4\u003e\n\u003cp\u003eAll four pumps stop dosing until power is restored, since they draw from the one supply. There's no battery backup built into the kit.\u003c\/p\u003e\n\u003ch4\u003eCan I run all four pumps on different schedules?\u003c\/h4\u003e\n\u003cp\u003eYes. Each pump is scheduled independently through the Mobius app — sharing a power rail doesn't mean sharing a dosing schedule.\u003c\/p\u003e","brand":"EcoTech Marine","offers":[{"title":"Default Title","offer_id":55293350871331,"sku":"MPVXF-1","price":1299.9,"currency_code":"AUD","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0972\/7236\/5347\/files\/versa-dosing-pump-4-pumps-ba-43876725195043.webp?v=1790240280"}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0972\/7236\/5347\/collections\/13327_pH-20computer-Set_16159052710_a2fb2bfa-6429-484b-8a46-5f9d69fe46d8.png?v=1788252603","url":"https:\/\/nicksaquariumoceanariumterrarium.com.au\/collections\/sw-controllers-dosing-automation.oembed","provider":"Nicks AOT","version":"1.0","type":"link"}